Logo Search packages:      
Sourcecode: linux version File versions  Download package

parport_pc.c

/* Low-level parallel-port routines for 8255-based PC-style hardware.
 * 
 * Authors: Phil Blundell <philb@gnu.org>
 *          Tim Waugh <tim@cyberelk.demon.co.uk>
 *        Jose Renau <renau@acm.org>
 *          David Campbell
 *          Andrea Arcangeli
 *
 * based on work by Grant Guenther <grant@torque.net> and Phil Blundell.
 *
 * Cleaned up include files - Russell King <linux@arm.uk.linux.org>
 * DMA support - Bert De Jonghe <bert@sophis.be>
 * Many ECP bugs fixed.  Fred Barnes & Jamie Lokier, 1999
 * More PCI support now conditional on CONFIG_PCI, 03/2001, Paul G. 
 * Various hacks, Fred Barnes, 04/2001
 * Updated probing logic - Adam Belay <ambx1@neo.rr.com>
 */

/* This driver should work with any hardware that is broadly compatible
 * with that in the IBM PC.  This applies to the majority of integrated
 * I/O chipsets that are commonly available.  The expected register
 * layout is:
 *
 *    base+0            data
 *    base+1            status
 *    base+2            control
 *
 * In addition, there are some optional registers:
 *
 *    base+3            EPP address
 *    base+4            EPP data
 *    base+0x400  ECP config A
 *    base+0x401  ECP config B
 *    base+0x402  ECP control
 *
 * All registers are 8 bits wide and read/write.  If your hardware differs
 * only in register addresses (eg because your registers are on 32-bit
 * word boundaries) then you can alter the constants in parport_pc.h to
 * accommodate this.
 *
 * Note that the ECP registers may not start at offset 0x400 for PCI cards,
 * but rather will start at port->base_hi.
 */

#include <linux/module.h>
#include <linux/init.h>
#include <linux/sched.h>
#include <linux/delay.h>
#include <linux/errno.h>
#include <linux/interrupt.h>
#include <linux/ioport.h>
#include <linux/kernel.h>
#include <linux/slab.h>
#include <linux/dma-mapping.h>
#include <linux/pci.h>
#include <linux/pnp.h>
#include <linux/platform_device.h>
#include <linux/sysctl.h>

#include <asm/io.h>
#include <asm/dma.h>
#include <asm/uaccess.h>

#include <linux/parport.h>
#include <linux/parport_pc.h>
#include <linux/via.h>
#include <asm/parport.h>

#define PARPORT_PC_MAX_PORTS PARPORT_MAX

#ifdef CONFIG_ISA_DMA_API
#define HAS_DMA
#endif

/* ECR modes */
#define ECR_SPP 00
#define ECR_PS2 01
#define ECR_PPF 02
#define ECR_ECP 03
#define ECR_EPP 04
#define ECR_VND 05
#define ECR_TST 06
#define ECR_CNF 07
#define ECR_MODE_MASK 0xe0
#define ECR_WRITE(p,v) frob_econtrol((p),0xff,(v))

#undef DEBUG

#ifdef DEBUG
#define DPRINTK  printk
#else
#define DPRINTK(stuff...)
#endif


#define NR_SUPERIOS 3
static struct superio_struct {      /* For Super-IO chips autodetection */
      int io;
      int irq;
      int dma;
} superios[NR_SUPERIOS] = { {0,},};

static int user_specified;
#if defined(CONFIG_PARPORT_PC_SUPERIO) || \
       (defined(CONFIG_PARPORT_1284) && defined(CONFIG_PARPORT_PC_FIFO))
static int verbose_probing;
#endif
static int pci_registered_parport;
static int pnp_registered_parport;

/* frob_control, but for ECR */
static void frob_econtrol (struct parport *pb, unsigned char m,
                     unsigned char v)
{
      unsigned char ectr = 0;

      if (m != 0xff)
            ectr = inb (ECONTROL (pb));

      DPRINTK (KERN_DEBUG "frob_econtrol(%02x,%02x): %02x -> %02x\n",
            m, v, ectr, (ectr & ~m) ^ v);

      outb ((ectr & ~m) ^ v, ECONTROL (pb));
}

static __inline__ void frob_set_mode (struct parport *p, int mode)
{
      frob_econtrol (p, ECR_MODE_MASK, mode << 5);
}

#ifdef CONFIG_PARPORT_PC_FIFO
/* Safely change the mode bits in the ECR 
   Returns:
          0    : Success
         -EBUSY: Could not drain FIFO in some finite amount of time,
               mode not changed!
 */
static int change_mode(struct parport *p, int m)
{
      const struct parport_pc_private *priv = p->physport->private_data;
      unsigned char oecr;
      int mode;

      DPRINTK(KERN_INFO "parport change_mode ECP-ISA to mode 0x%02x\n",m);

      if (!priv->ecr) {
            printk (KERN_DEBUG "change_mode: but there's no ECR!\n");
            return 0;
      }

      /* Bits <7:5> contain the mode. */
      oecr = inb (ECONTROL (p));
      mode = (oecr >> 5) & 0x7;
      if (mode == m) return 0;

      if (mode >= 2 && !(priv->ctr & 0x20)) {
            /* This mode resets the FIFO, so we may
             * have to wait for it to drain first. */
            unsigned long expire = jiffies + p->physport->cad->timeout;
            int counter;
            switch (mode) {
            case ECR_PPF: /* Parallel Port FIFO mode */
            case ECR_ECP: /* ECP Parallel Port mode */
                  /* Busy wait for 200us */
                  for (counter = 0; counter < 40; counter++) {
                        if (inb (ECONTROL (p)) & 0x01)
                              break;
                        if (signal_pending (current)) break;
                        udelay (5);
                  }

                  /* Poll slowly. */
                  while (!(inb (ECONTROL (p)) & 0x01)) {
                        if (time_after_eq (jiffies, expire))
                              /* The FIFO is stuck. */
                              return -EBUSY;
                        schedule_timeout_interruptible(msecs_to_jiffies(10));
                        if (signal_pending (current))
                              break;
                  }
            }
      }

      if (mode >= 2 && m >= 2) {
            /* We have to go through mode 001 */
            oecr &= ~(7 << 5);
            oecr |= ECR_PS2 << 5;
            ECR_WRITE (p, oecr);
      }

      /* Set the mode. */
      oecr &= ~(7 << 5);
      oecr |= m << 5;
      ECR_WRITE (p, oecr);
      return 0;
}

#ifdef CONFIG_PARPORT_1284
/* Find FIFO lossage; FIFO is reset */
#if 0
static int get_fifo_residue (struct parport *p)
{
      int residue;
      int cnfga;
      const struct parport_pc_private *priv = p->physport->private_data;

      /* Adjust for the contents of the FIFO. */
      for (residue = priv->fifo_depth; ; residue--) {
            if (inb (ECONTROL (p)) & 0x2)
                        /* Full up. */
                  break;

            outb (0, FIFO (p));
      }

      printk (KERN_DEBUG "%s: %d PWords were left in FIFO\n", p->name,
            residue);

      /* Reset the FIFO. */
      frob_set_mode (p, ECR_PS2);

      /* Now change to config mode and clean up. FIXME */
      frob_set_mode (p, ECR_CNF);
      cnfga = inb (CONFIGA (p));
      printk (KERN_DEBUG "%s: cnfgA contains 0x%02x\n", p->name, cnfga);

      if (!(cnfga & (1<<2))) {
            printk (KERN_DEBUG "%s: Accounting for extra byte\n", p->name);
            residue++;
      }

      /* Don't care about partial PWords until support is added for
       * PWord != 1 byte. */

      /* Back to PS2 mode. */
      frob_set_mode (p, ECR_PS2);

      DPRINTK (KERN_DEBUG "*** get_fifo_residue: done residue collecting (ecr = 0x%2.2x)\n", inb (ECONTROL (p)));
      return residue;
}
#endif  /*  0 */
#endif /* IEEE 1284 support */
#endif /* FIFO support */

/*
 * Clear TIMEOUT BIT in EPP MODE
 *
 * This is also used in SPP detection.
 */
static int clear_epp_timeout(struct parport *pb)
{
      unsigned char r;

      if (!(parport_pc_read_status(pb) & 0x01))
            return 1;

      /* To clear timeout some chips require double read */
      parport_pc_read_status(pb);
      r = parport_pc_read_status(pb);
      outb (r | 0x01, STATUS (pb)); /* Some reset by writing 1 */
      outb (r & 0xfe, STATUS (pb)); /* Others by writing 0 */
      r = parport_pc_read_status(pb);

      return !(r & 0x01);
}

/*
 * Access functions.
 *
 * Most of these aren't static because they may be used by the
 * parport_xxx_yyy macros.  extern __inline__ versions of several
 * of these are in parport_pc.h.
 */

static void parport_pc_init_state(struct pardevice *dev, struct parport_state *s)
{
      s->u.pc.ctr = 0xc;
      if (dev->irq_func &&
          dev->port->irq != PARPORT_IRQ_NONE)
            /* Set ackIntEn */
            s->u.pc.ctr |= 0x10;

      s->u.pc.ecr = 0x34; /* NetMos chip can cause problems 0x24;
                       * D.Gruszka VScom */
}

static void parport_pc_save_state(struct parport *p, struct parport_state *s)
{
      const struct parport_pc_private *priv = p->physport->private_data;
      s->u.pc.ctr = priv->ctr;
      if (priv->ecr)
            s->u.pc.ecr = inb (ECONTROL (p));
}

static void parport_pc_restore_state(struct parport *p, struct parport_state *s)
{
      struct parport_pc_private *priv = p->physport->private_data;
      register unsigned char c = s->u.pc.ctr & priv->ctr_writable;
      outb (c, CONTROL (p));
      priv->ctr = c;
      if (priv->ecr)
            ECR_WRITE (p, s->u.pc.ecr);
}

#ifdef CONFIG_PARPORT_1284
static size_t parport_pc_epp_read_data (struct parport *port, void *buf,
                              size_t length, int flags)
{
      size_t got = 0;

      if (flags & PARPORT_W91284PIC) {
            unsigned char status;
            size_t left = length;

            /* use knowledge about data lines..:
             *  nFault is 0 if there is at least 1 byte in the Warp's FIFO
             *  pError is 1 if there are 16 bytes in the Warp's FIFO
             */
            status = inb (STATUS (port));

            while (!(status & 0x08) && (got < length)) {
                  if ((left >= 16) && (status & 0x20) && !(status & 0x08)) {
                        /* can grab 16 bytes from warp fifo */
                        if (!((long)buf & 0x03)) {
                              insl (EPPDATA (port), buf, 4);
                        } else {
                              insb (EPPDATA (port), buf, 16);
                        }
                        buf += 16;
                        got += 16;
                        left -= 16;
                  } else {
                        /* grab single byte from the warp fifo */
                        *((char *)buf) = inb (EPPDATA (port));
                        buf++;
                        got++;
                        left--;
                  }
                  status = inb (STATUS (port));
                  if (status & 0x01) {
                        /* EPP timeout should never occur... */
                        printk (KERN_DEBUG "%s: EPP timeout occurred while talking to "
                              "w91284pic (should not have done)\n", port->name);
                        clear_epp_timeout (port);
                  }
            }
            return got;
      }
      if ((flags & PARPORT_EPP_FAST) && (length > 1)) {
            if (!(((long)buf | length) & 0x03)) {
                  insl (EPPDATA (port), buf, (length >> 2));
            } else {
                  insb (EPPDATA (port), buf, length);
            }
            if (inb (STATUS (port)) & 0x01) {
                  clear_epp_timeout (port);
                  return -EIO;
            }
            return length;
      }
      for (; got < length; got++) {
            *((char*)buf) = inb (EPPDATA(port));
            buf++;
            if (inb (STATUS (port)) & 0x01) {
                  /* EPP timeout */
                  clear_epp_timeout (port);
                  break;
            }
      }

      return got;
}

static size_t parport_pc_epp_write_data (struct parport *port, const void *buf,
                               size_t length, int flags)
{
      size_t written = 0;

      if ((flags & PARPORT_EPP_FAST) && (length > 1)) {
            if (!(((long)buf | length) & 0x03)) {
                  outsl (EPPDATA (port), buf, (length >> 2));
            } else {
                  outsb (EPPDATA (port), buf, length);
            }
            if (inb (STATUS (port)) & 0x01) {
                  clear_epp_timeout (port);
                  return -EIO;
            }
            return length;
      }
      for (; written < length; written++) {
            outb (*((char*)buf), EPPDATA(port));
            buf++;
            if (inb (STATUS(port)) & 0x01) {
                  clear_epp_timeout (port);
                  break;
            }
      }

      return written;
}

static size_t parport_pc_epp_read_addr (struct parport *port, void *buf,
                              size_t length, int flags)
{
      size_t got = 0;

      if ((flags & PARPORT_EPP_FAST) && (length > 1)) {
            insb (EPPADDR (port), buf, length);
            if (inb (STATUS (port)) & 0x01) {
                  clear_epp_timeout (port);
                  return -EIO;
            }
            return length;
      }
      for (; got < length; got++) {
            *((char*)buf) = inb (EPPADDR (port));
            buf++;
            if (inb (STATUS (port)) & 0x01) {
                  clear_epp_timeout (port);
                  break;
            }
      }

      return got;
}

static size_t parport_pc_epp_write_addr (struct parport *port,
                               const void *buf, size_t length,
                               int flags)
{
      size_t written = 0;

      if ((flags & PARPORT_EPP_FAST) && (length > 1)) {
            outsb (EPPADDR (port), buf, length);
            if (inb (STATUS (port)) & 0x01) {
                  clear_epp_timeout (port);
                  return -EIO;
            }
            return length;
      }
      for (; written < length; written++) {
            outb (*((char*)buf), EPPADDR (port));
            buf++;
            if (inb (STATUS (port)) & 0x01) {
                  clear_epp_timeout (port);
                  break;
            }
      }

      return written;
}

static size_t parport_pc_ecpepp_read_data (struct parport *port, void *buf,
                                 size_t length, int flags)
{
      size_t got;

      frob_set_mode (port, ECR_EPP);
      parport_pc_data_reverse (port);
      parport_pc_write_control (port, 0x4);
      got = parport_pc_epp_read_data (port, buf, length, flags);
      frob_set_mode (port, ECR_PS2);

      return got;
}

static size_t parport_pc_ecpepp_write_data (struct parport *port,
                                  const void *buf, size_t length,
                                  int flags)
{
      size_t written;

      frob_set_mode (port, ECR_EPP);
      parport_pc_write_control (port, 0x4);
      parport_pc_data_forward (port);
      written = parport_pc_epp_write_data (port, buf, length, flags);
      frob_set_mode (port, ECR_PS2);

      return written;
}

static size_t parport_pc_ecpepp_read_addr (struct parport *port, void *buf,
                                 size_t length, int flags)
{
      size_t got;

      frob_set_mode (port, ECR_EPP);
      parport_pc_data_reverse (port);
      parport_pc_write_control (port, 0x4);
      got = parport_pc_epp_read_addr (port, buf, length, flags);
      frob_set_mode (port, ECR_PS2);

      return got;
}

static size_t parport_pc_ecpepp_write_addr (struct parport *port,
                                  const void *buf, size_t length,
                                  int flags)
{
      size_t written;

      frob_set_mode (port, ECR_EPP);
      parport_pc_write_control (port, 0x4);
      parport_pc_data_forward (port);
      written = parport_pc_epp_write_addr (port, buf, length, flags);
      frob_set_mode (port, ECR_PS2);

      return written;
}
#endif /* IEEE 1284 support */

#ifdef CONFIG_PARPORT_PC_FIFO
static size_t parport_pc_fifo_write_block_pio (struct parport *port,
                                     const void *buf, size_t length)
{
      int ret = 0;
      const unsigned char *bufp = buf;
      size_t left = length;
      unsigned long expire = jiffies + port->physport->cad->timeout;
      const int fifo = FIFO (port);
      int poll_for = 8; /* 80 usecs */
      const struct parport_pc_private *priv = port->physport->private_data;
      const int fifo_depth = priv->fifo_depth;

      port = port->physport;

      /* We don't want to be interrupted every character. */
      parport_pc_disable_irq (port);
      /* set nErrIntrEn and serviceIntr */
      frob_econtrol (port, (1<<4) | (1<<2), (1<<4) | (1<<2));

      /* Forward mode. */
      parport_pc_data_forward (port); /* Must be in PS2 mode */

      while (left) {
            unsigned char byte;
            unsigned char ecrval = inb (ECONTROL (port));
            int i = 0;

            if (need_resched() && time_before (jiffies, expire))
                  /* Can't yield the port. */
                  schedule ();

            /* Anyone else waiting for the port? */
            if (port->waithead) {
                  printk (KERN_DEBUG "Somebody wants the port\n");
                  break;
            }

            if (ecrval & 0x02) {
                  /* FIFO is full. Wait for interrupt. */

                  /* Clear serviceIntr */
                  ECR_WRITE (port, ecrval & ~(1<<2));
            false_alarm:
                  ret = parport_wait_event (port, HZ);
                  if (ret < 0) break;
                  ret = 0;
                  if (!time_before (jiffies, expire)) {
                        /* Timed out. */
                        printk (KERN_DEBUG "FIFO write timed out\n");
                        break;
                  }
                  ecrval = inb (ECONTROL (port));
                  if (!(ecrval & (1<<2))) {
                        if (need_resched() &&
                            time_before (jiffies, expire))
                              schedule ();

                        goto false_alarm;
                  }

                  continue;
            }

            /* Can't fail now. */
            expire = jiffies + port->cad->timeout;

      poll:
            if (signal_pending (current))
                  break;

            if (ecrval & 0x01) {
                  /* FIFO is empty. Blast it full. */
                  const int n = left < fifo_depth ? left : fifo_depth;
                  outsb (fifo, bufp, n);
                  bufp += n;
                  left -= n;

                  /* Adjust the poll time. */
                  if (i < (poll_for - 2)) poll_for--;
                  continue;
            } else if (i++ < poll_for) {
                  udelay (10);
                  ecrval = inb (ECONTROL (port));
                  goto poll;
            }

            /* Half-full (call me an optimist) */
            byte = *bufp++;
            outb (byte, fifo);
            left--;
        }

dump_parport_state ("leave fifo_write_block_pio", port);
      return length - left;
}

#ifdef HAS_DMA
static size_t parport_pc_fifo_write_block_dma (struct parport *port,
                                     const void *buf, size_t length)
{
      int ret = 0;
      unsigned long dmaflag;
      size_t left = length;
      const struct parport_pc_private *priv = port->physport->private_data;
      struct device *dev = port->physport->dev;
      dma_addr_t dma_addr, dma_handle;
      size_t maxlen = 0x10000; /* max 64k per DMA transfer */
      unsigned long start = (unsigned long) buf;
      unsigned long end = (unsigned long) buf + length - 1;

dump_parport_state ("enter fifo_write_block_dma", port);
      if (end < MAX_DMA_ADDRESS) {
            /* If it would cross a 64k boundary, cap it at the end. */
            if ((start ^ end) & ~0xffffUL)
                  maxlen = 0x10000 - (start & 0xffff);

            dma_addr = dma_handle = dma_map_single(dev, (void *)buf, length,
                                           DMA_TO_DEVICE);
        } else {
            /* above 16 MB we use a bounce buffer as ISA-DMA is not possible */
            maxlen   = PAGE_SIZE;          /* sizeof(priv->dma_buf) */
            dma_addr = priv->dma_handle;
            dma_handle = 0;
      }

      port = port->physport;

      /* We don't want to be interrupted every character. */
      parport_pc_disable_irq (port);
      /* set nErrIntrEn and serviceIntr */
      frob_econtrol (port, (1<<4) | (1<<2), (1<<4) | (1<<2));

      /* Forward mode. */
      parport_pc_data_forward (port); /* Must be in PS2 mode */

      while (left) {
            unsigned long expire = jiffies + port->physport->cad->timeout;

            size_t count = left;

            if (count > maxlen)
                  count = maxlen;

            if (!dma_handle)   /* bounce buffer ! */
                  memcpy(priv->dma_buf, buf, count);

            dmaflag = claim_dma_lock();
            disable_dma(port->dma);
            clear_dma_ff(port->dma);
            set_dma_mode(port->dma, DMA_MODE_WRITE);
            set_dma_addr(port->dma, dma_addr);
            set_dma_count(port->dma, count);

            /* Set DMA mode */
            frob_econtrol (port, 1<<3, 1<<3);

            /* Clear serviceIntr */
            frob_econtrol (port, 1<<2, 0);

            enable_dma(port->dma);
            release_dma_lock(dmaflag);

            /* assume DMA will be successful */
            left -= count;
            buf  += count;
            if (dma_handle) dma_addr += count;

            /* Wait for interrupt. */
      false_alarm:
            ret = parport_wait_event (port, HZ);
            if (ret < 0) break;
            ret = 0;
            if (!time_before (jiffies, expire)) {
                  /* Timed out. */
                  printk (KERN_DEBUG "DMA write timed out\n");
                  break;
            }
            /* Is serviceIntr set? */
            if (!(inb (ECONTROL (port)) & (1<<2))) {
                  cond_resched();

                  goto false_alarm;
            }

            dmaflag = claim_dma_lock();
            disable_dma(port->dma);
            clear_dma_ff(port->dma);
            count = get_dma_residue(port->dma);
            release_dma_lock(dmaflag);

            cond_resched(); /* Can't yield the port. */

            /* Anyone else waiting for the port? */
            if (port->waithead) {
                  printk (KERN_DEBUG "Somebody wants the port\n");
                  break;
            }

            /* update for possible DMA residue ! */
            buf  -= count;
            left += count;
            if (dma_handle) dma_addr -= count;
      }

      /* Maybe got here through break, so adjust for DMA residue! */
      dmaflag = claim_dma_lock();
      disable_dma(port->dma);
      clear_dma_ff(port->dma);
      left += get_dma_residue(port->dma);
      release_dma_lock(dmaflag);

      /* Turn off DMA mode */
      frob_econtrol (port, 1<<3, 0);

      if (dma_handle)
            dma_unmap_single(dev, dma_handle, length, DMA_TO_DEVICE);

dump_parport_state ("leave fifo_write_block_dma", port);
      return length - left;
}
#endif

static inline size_t parport_pc_fifo_write_block(struct parport *port,
                                     const void *buf, size_t length)
{
#ifdef HAS_DMA
      if (port->dma != PARPORT_DMA_NONE)
            return parport_pc_fifo_write_block_dma (port, buf, length);
#endif
      return parport_pc_fifo_write_block_pio (port, buf, length);
}

/* Parallel Port FIFO mode (ECP chipsets) */
static size_t parport_pc_compat_write_block_pio (struct parport *port,
                                     const void *buf, size_t length,
                                     int flags)
{
      size_t written;
      int r;
      unsigned long expire;
      const struct parport_pc_private *priv = port->physport->private_data;

      /* Special case: a timeout of zero means we cannot call schedule().
       * Also if O_NONBLOCK is set then use the default implementation. */
      if (port->physport->cad->timeout <= PARPORT_INACTIVITY_O_NONBLOCK)
            return parport_ieee1284_write_compat (port, buf,
                                          length, flags);

      /* Set up parallel port FIFO mode.*/
      parport_pc_data_forward (port); /* Must be in PS2 mode */
      parport_pc_frob_control (port, PARPORT_CONTROL_STROBE, 0);
      r = change_mode (port, ECR_PPF); /* Parallel port FIFO */
      if (r)  printk (KERN_DEBUG "%s: Warning change_mode ECR_PPF failed\n", port->name);

      port->physport->ieee1284.phase = IEEE1284_PH_FWD_DATA;

      /* Write the data to the FIFO. */
      written = parport_pc_fifo_write_block(port, buf, length);

      /* Finish up. */
      /* For some hardware we don't want to touch the mode until
       * the FIFO is empty, so allow 4 seconds for each position
       * in the fifo.
       */
        expire = jiffies + (priv->fifo_depth * HZ * 4);
      do {
            /* Wait for the FIFO to empty */
            r = change_mode (port, ECR_PS2);
            if (r != -EBUSY) {
                  break;
            }
      } while (time_before (jiffies, expire));
      if (r == -EBUSY) {

            printk (KERN_DEBUG "%s: FIFO is stuck\n", port->name);

            /* Prevent further data transfer. */
            frob_set_mode (port, ECR_TST);

            /* Adjust for the contents of the FIFO. */
            for (written -= priv->fifo_depth; ; written++) {
                  if (inb (ECONTROL (port)) & 0x2) {
                        /* Full up. */
                        break;
                  }
                  outb (0, FIFO (port));
            }

            /* Reset the FIFO and return to PS2 mode. */
            frob_set_mode (port, ECR_PS2);
      }

      r = parport_wait_peripheral (port,
                             PARPORT_STATUS_BUSY,
                             PARPORT_STATUS_BUSY);
      if (r)
            printk (KERN_DEBUG
                  "%s: BUSY timeout (%d) in compat_write_block_pio\n", 
                  port->name, r);

      port->physport->ieee1284.phase = IEEE1284_PH_FWD_IDLE;

      return written;
}

/* ECP */
#ifdef CONFIG_PARPORT_1284
static size_t parport_pc_ecp_write_block_pio (struct parport *port,
                                    const void *buf, size_t length,
                                    int flags)
{
      size_t written;
      int r;
      unsigned long expire;
      const struct parport_pc_private *priv = port->physport->private_data;

      /* Special case: a timeout of zero means we cannot call schedule().
       * Also if O_NONBLOCK is set then use the default implementation. */
      if (port->physport->cad->timeout <= PARPORT_INACTIVITY_O_NONBLOCK)
            return parport_ieee1284_ecp_write_data (port, buf,
                                          length, flags);

      /* Switch to forward mode if necessary. */
      if (port->physport->ieee1284.phase != IEEE1284_PH_FWD_IDLE) {
            /* Event 47: Set nInit high. */
            parport_frob_control (port,
                              PARPORT_CONTROL_INIT
                              | PARPORT_CONTROL_AUTOFD,
                              PARPORT_CONTROL_INIT
                              | PARPORT_CONTROL_AUTOFD);

            /* Event 49: PError goes high. */
            r = parport_wait_peripheral (port,
                                   PARPORT_STATUS_PAPEROUT,
                                   PARPORT_STATUS_PAPEROUT);
            if (r) {
                  printk (KERN_DEBUG "%s: PError timeout (%d) "
                        "in ecp_write_block_pio\n", port->name, r);
            }
      }

      /* Set up ECP parallel port mode.*/
      parport_pc_data_forward (port); /* Must be in PS2 mode */
      parport_pc_frob_control (port,
                         PARPORT_CONTROL_STROBE |
                         PARPORT_CONTROL_AUTOFD,
                         0);
      r = change_mode (port, ECR_ECP); /* ECP FIFO */
      if (r) printk (KERN_DEBUG "%s: Warning change_mode ECR_ECP failed\n", port->name);
      port->physport->ieee1284.phase = IEEE1284_PH_FWD_DATA;

      /* Write the data to the FIFO. */
      written = parport_pc_fifo_write_block(port, buf, length);

      /* Finish up. */
      /* For some hardware we don't want to touch the mode until
       * the FIFO is empty, so allow 4 seconds for each position
       * in the fifo.
       */
      expire = jiffies + (priv->fifo_depth * (HZ * 4));
      do {
            /* Wait for the FIFO to empty */
            r = change_mode (port, ECR_PS2);
            if (r != -EBUSY) {
                  break;
            }
      } while (time_before (jiffies, expire));
      if (r == -EBUSY) {

            printk (KERN_DEBUG "%s: FIFO is stuck\n", port->name);

            /* Prevent further data transfer. */
            frob_set_mode (port, ECR_TST);

            /* Adjust for the contents of the FIFO. */
            for (written -= priv->fifo_depth; ; written++) {
                  if (inb (ECONTROL (port)) & 0x2) {
                        /* Full up. */
                        break;
                  }
                  outb (0, FIFO (port));
            }

            /* Reset the FIFO and return to PS2 mode. */
            frob_set_mode (port, ECR_PS2);

            /* Host transfer recovery. */
            parport_pc_data_reverse (port); /* Must be in PS2 mode */
            udelay (5);
            parport_frob_control (port, PARPORT_CONTROL_INIT, 0);
            r = parport_wait_peripheral (port, PARPORT_STATUS_PAPEROUT, 0);
            if (r)
                  printk (KERN_DEBUG "%s: PE,1 timeout (%d) "
                        "in ecp_write_block_pio\n", port->name, r);

            parport_frob_control (port,
                              PARPORT_CONTROL_INIT,
                              PARPORT_CONTROL_INIT);
            r = parport_wait_peripheral (port,
                                   PARPORT_STATUS_PAPEROUT,
                                   PARPORT_STATUS_PAPEROUT);
                if (r)
                        printk (KERN_DEBUG "%s: PE,2 timeout (%d) "
                        "in ecp_write_block_pio\n", port->name, r);
      }

      r = parport_wait_peripheral (port,
                             PARPORT_STATUS_BUSY, 
                             PARPORT_STATUS_BUSY);
      if(r)
            printk (KERN_DEBUG
                  "%s: BUSY timeout (%d) in ecp_write_block_pio\n",
                  port->name, r);

      port->physport->ieee1284.phase = IEEE1284_PH_FWD_IDLE;

      return written;
}

#if 0
static size_t parport_pc_ecp_read_block_pio (struct parport *port,
                                   void *buf, size_t length,
                                   int flags)
{
      size_t left = length;
      size_t fifofull;
      int r;
      const int fifo = FIFO(port);
      const struct parport_pc_private *priv = port->physport->private_data;
      const int fifo_depth = priv->fifo_depth;
      char *bufp = buf;

      port = port->physport;
DPRINTK (KERN_DEBUG "parport_pc: parport_pc_ecp_read_block_pio\n");
dump_parport_state ("enter fcn", port);

      /* Special case: a timeout of zero means we cannot call schedule().
       * Also if O_NONBLOCK is set then use the default implementation. */
      if (port->cad->timeout <= PARPORT_INACTIVITY_O_NONBLOCK)
            return parport_ieee1284_ecp_read_data (port, buf,
                                           length, flags);

      if (port->ieee1284.mode == IEEE1284_MODE_ECPRLE) {
            /* If the peripheral is allowed to send RLE compressed
             * data, it is possible for a byte to expand to 128
             * bytes in the FIFO. */
            fifofull = 128;
      } else {
            fifofull = fifo_depth;
      }

      /* If the caller wants less than a full FIFO's worth of data,
       * go through software emulation.  Otherwise we may have to throw
       * away data. */
      if (length < fifofull)
            return parport_ieee1284_ecp_read_data (port, buf,
                                           length, flags);

      if (port->ieee1284.phase != IEEE1284_PH_REV_IDLE) {
            /* change to reverse-idle phase (must be in forward-idle) */

            /* Event 38: Set nAutoFd low (also make sure nStrobe is high) */
            parport_frob_control (port,
                              PARPORT_CONTROL_AUTOFD
                              | PARPORT_CONTROL_STROBE,
                              PARPORT_CONTROL_AUTOFD);
            parport_pc_data_reverse (port); /* Must be in PS2 mode */
            udelay (5);
            /* Event 39: Set nInit low to initiate bus reversal */
            parport_frob_control (port,
                              PARPORT_CONTROL_INIT,
                              0);
            /* Event 40: Wait for  nAckReverse (PError) to go low */
            r = parport_wait_peripheral (port, PARPORT_STATUS_PAPEROUT, 0);
                if (r) {
                        printk (KERN_DEBUG "%s: PE timeout Event 40 (%d) "
                        "in ecp_read_block_pio\n", port->name, r);
                  return 0;
            }
      }

      /* Set up ECP FIFO mode.*/
/*    parport_pc_frob_control (port,
                         PARPORT_CONTROL_STROBE |
                         PARPORT_CONTROL_AUTOFD,
                         PARPORT_CONTROL_AUTOFD); */
      r = change_mode (port, ECR_ECP); /* ECP FIFO */
      if (r) printk (KERN_DEBUG "%s: Warning change_mode ECR_ECP failed\n", port->name);

      port->ieee1284.phase = IEEE1284_PH_REV_DATA;

      /* the first byte must be collected manually */
dump_parport_state ("pre 43", port);
      /* Event 43: Wait for nAck to go low */
      r = parport_wait_peripheral (port, PARPORT_STATUS_ACK, 0);
      if (r) {
            /* timed out while reading -- no data */
            printk (KERN_DEBUG "PIO read timed out (initial byte)\n");
            goto out_no_data;
      }
      /* read byte */
      *bufp++ = inb (DATA (port));
      left--;
dump_parport_state ("43-44", port);
      /* Event 44: nAutoFd (HostAck) goes high to acknowledge */
      parport_pc_frob_control (port,
                         PARPORT_CONTROL_AUTOFD,
                         0);
dump_parport_state ("pre 45", port);
      /* Event 45: Wait for nAck to go high */
/*    r = parport_wait_peripheral (port, PARPORT_STATUS_ACK, PARPORT_STATUS_ACK); */
dump_parport_state ("post 45", port);
r = 0;
      if (r) {
            /* timed out while waiting for peripheral to respond to ack */
            printk (KERN_DEBUG "ECP PIO read timed out (waiting for nAck)\n");

            /* keep hold of the byte we've got already */
            goto out_no_data;
      }
      /* Event 46: nAutoFd (HostAck) goes low to accept more data */
      parport_pc_frob_control (port,
                         PARPORT_CONTROL_AUTOFD,
                         PARPORT_CONTROL_AUTOFD);


dump_parport_state ("rev idle", port);
      /* Do the transfer. */
      while (left > fifofull) {
            int ret;
            unsigned long expire = jiffies + port->cad->timeout;
            unsigned char ecrval = inb (ECONTROL (port));

            if (need_resched() && time_before (jiffies, expire))
                  /* Can't yield the port. */
                  schedule ();

            /* At this point, the FIFO may already be full. In
                 * that case ECP is already holding back the
                 * peripheral (assuming proper design) with a delayed
                 * handshake.  Work fast to avoid a peripheral
                 * timeout.  */

            if (ecrval & 0x01) {
                  /* FIFO is empty. Wait for interrupt. */
dump_parport_state ("FIFO empty", port);

                  /* Anyone else waiting for the port? */
                  if (port->waithead) {
                        printk (KERN_DEBUG "Somebody wants the port\n");
                        break;
                  }

                  /* Clear serviceIntr */
                  ECR_WRITE (port, ecrval & ~(1<<2));
            false_alarm:
dump_parport_state ("waiting", port);
                  ret = parport_wait_event (port, HZ);
DPRINTK (KERN_DEBUG "parport_wait_event returned %d\n", ret);
                  if (ret < 0)
                        break;
                  ret = 0;
                  if (!time_before (jiffies, expire)) {
                        /* Timed out. */
dump_parport_state ("timeout", port);
                        printk (KERN_DEBUG "PIO read timed out\n");
                        break;
                  }
                  ecrval = inb (ECONTROL (port));
                  if (!(ecrval & (1<<2))) {
                        if (need_resched() &&
                            time_before (jiffies, expire)) {
                              schedule ();
                        }
                        goto false_alarm;
                  }

                  /* Depending on how the FIFO threshold was
                         * set, how long interrupt service took, and
                         * how fast the peripheral is, we might be
                         * lucky and have a just filled FIFO. */
                  continue;
            }

            if (ecrval & 0x02) {
                  /* FIFO is full. */
dump_parport_state ("FIFO full", port);
                  insb (fifo, bufp, fifo_depth);
                  bufp += fifo_depth;
                  left -= fifo_depth;
                  continue;
            }

DPRINTK (KERN_DEBUG "*** ecp_read_block_pio: reading one byte from the FIFO\n");

            /* FIFO not filled.  We will cycle this loop for a while
                 * and either the peripheral will fill it faster,
                 * tripping a fast empty with insb, or we empty it. */
            *bufp++ = inb (fifo);
            left--;
      }

      /* scoop up anything left in the FIFO */
      while (left && !(inb (ECONTROL (port) & 0x01))) {
            *bufp++ = inb (fifo);
            left--;
      }

      port->ieee1284.phase = IEEE1284_PH_REV_IDLE;
dump_parport_state ("rev idle2", port);

out_no_data:

      /* Go to forward idle mode to shut the peripheral up (event 47). */
      parport_frob_control (port, PARPORT_CONTROL_INIT, PARPORT_CONTROL_INIT);

      /* event 49: PError goes high */
      r = parport_wait_peripheral (port,
                             PARPORT_STATUS_PAPEROUT,
                             PARPORT_STATUS_PAPEROUT);
      if (r) {
            printk (KERN_DEBUG
                  "%s: PE timeout FWDIDLE (%d) in ecp_read_block_pio\n",
                  port->name, r);
      }

      port->ieee1284.phase = IEEE1284_PH_FWD_IDLE;

      /* Finish up. */
      {
            int lost = get_fifo_residue (port);
            if (lost)
                  /* Shouldn't happen with compliant peripherals. */
                  printk (KERN_DEBUG "%s: DATA LOSS (%d bytes)!\n",
                        port->name, lost);
      }

dump_parport_state ("fwd idle", port);
      return length - left;
}
#endif  /*  0  */
#endif /* IEEE 1284 support */
#endif /* Allowed to use FIFO/DMA */


/*
 *    ******************************************
 *    INITIALISATION AND MODULE STUFF BELOW HERE
 *    ******************************************
 */

/* GCC is not inlining extern inline function later overwriten to non-inline,
   so we use outlined_ variants here.  */
static const struct parport_operations parport_pc_ops =
{
      .write_data = parport_pc_write_data,
      .read_data  = parport_pc_read_data,

      .write_control    = parport_pc_write_control,
      .read_control     = parport_pc_read_control,
      .frob_control     = parport_pc_frob_control,

      .read_status      = parport_pc_read_status,

      .enable_irq = parport_pc_enable_irq,
      .disable_irq      = parport_pc_disable_irq,

      .data_forward     = parport_pc_data_forward,
      .data_reverse     = parport_pc_data_reverse,

      .init_state = parport_pc_init_state,
      .save_state = parport_pc_save_state,
      .restore_state    = parport_pc_restore_state,

      .epp_write_data   = parport_ieee1284_epp_write_data,
      .epp_read_data    = parport_ieee1284_epp_read_data,
      .epp_write_addr   = parport_ieee1284_epp_write_addr,
      .epp_read_addr    = parport_ieee1284_epp_read_addr,

      .ecp_write_data   = parport_ieee1284_ecp_write_data,
      .ecp_read_data    = parport_ieee1284_ecp_read_data,
      .ecp_write_addr   = parport_ieee1284_ecp_write_addr,

      .compat_write_data      = parport_ieee1284_write_compat,
      .nibble_read_data = parport_ieee1284_read_nibble,
      .byte_read_data         = parport_ieee1284_read_byte,

      .owner            = THIS_MODULE,
};

#ifdef CONFIG_PARPORT_PC_SUPERIO
/* Super-IO chipset detection, Winbond, SMSC */
static void __devinit show_parconfig_smsc37c669(int io, int key)
{
      int cr1,cr4,cra,cr23,cr26,cr27,i=0;
      static const char *const modes[]={
            "SPP and Bidirectional (PS/2)",
            "EPP and SPP",
            "ECP",
            "ECP and EPP" };

      outb(key,io);
      outb(key,io);
      outb(1,io);
      cr1=inb(io+1);
      outb(4,io);
      cr4=inb(io+1);
      outb(0x0a,io);
      cra=inb(io+1);
      outb(0x23,io);
      cr23=inb(io+1);
      outb(0x26,io);
      cr26=inb(io+1);
      outb(0x27,io);
      cr27=inb(io+1);
      outb(0xaa,io);

      if (verbose_probing) {
            printk (KERN_INFO "SMSC 37c669 LPT Config: cr_1=0x%02x, 4=0x%02x, "
                  "A=0x%2x, 23=0x%02x, 26=0x%02x, 27=0x%02x\n",
                  cr1,cr4,cra,cr23,cr26,cr27);
            
            /* The documentation calls DMA and IRQ-Lines by letters, so
               the board maker can/will wire them
               appropriately/randomly...  G=reserved H=IDE-irq, */
            printk (KERN_INFO "SMSC LPT Config: io=0x%04x, irq=%c, dma=%c, "
                  "fifo threshold=%d\n", cr23*4,
                  (cr27 &0x0f) ? 'A'-1+(cr27 &0x0f): '-',
                  (cr26 &0x0f) ? 'A'-1+(cr26 &0x0f): '-', cra & 0x0f);
            printk(KERN_INFO "SMSC LPT Config: enabled=%s power=%s\n",
                   (cr23*4 >=0x100) ?"yes":"no", (cr1 & 4) ? "yes" : "no");
            printk(KERN_INFO "SMSC LPT Config: Port mode=%s, EPP version =%s\n",
                   (cr1 & 0x08 ) ? "Standard mode only (SPP)" : modes[cr4 & 0x03], 
                   (cr4 & 0x40) ? "1.7" : "1.9");
      }
            
      /* Heuristics !  BIOS setup for this mainboard device limits
         the choices to standard settings, i.e. io-address and IRQ
         are related, however DMA can be 1 or 3, assume DMA_A=DMA1,
         DMA_C=DMA3 (this is true e.g. for TYAN 1564D Tomcat IV) */
      if(cr23*4 >=0x100) { /* if active */
            while((superios[i].io!= 0) && (i<NR_SUPERIOS))
                  i++;
            if(i==NR_SUPERIOS)
                  printk(KERN_INFO "Super-IO: too many chips!\n");
            else {
                  int d;
                  switch (cr23*4) {
                        case 0x3bc:
                              superios[i].io = 0x3bc;
                              superios[i].irq = 7;
                              break;
                        case 0x378:
                              superios[i].io = 0x378;
                              superios[i].irq = 7;
                              break;
                        case 0x278:
                              superios[i].io = 0x278;
                              superios[i].irq = 5;
                  }
                  d=(cr26 &0x0f);
                  if((d==1) || (d==3)) 
                        superios[i].dma= d;
                  else
                        superios[i].dma= PARPORT_DMA_NONE;
            }
      }
}


static void __devinit show_parconfig_winbond(int io, int key)
{
      int cr30,cr60,cr61,cr70,cr74,crf0,i=0;
      static const char *const modes[] = {
            "Standard (SPP) and Bidirectional(PS/2)", /* 0 */
            "EPP-1.9 and SPP",
            "ECP",
            "ECP and EPP-1.9",
            "Standard (SPP)",
            "EPP-1.7 and SPP",            /* 5 */
            "undefined!",
            "ECP and EPP-1.7" };
      static char *const irqtypes[] = {
            "pulsed low, high-Z",
            "follows nACK" };
            
      /* The registers are called compatible-PnP because the
           register layout is modelled after ISA-PnP, the access
           method is just another ... */
      outb(key,io);
      outb(key,io);
      outb(0x07,io);   /* Register 7: Select Logical Device */
      outb(0x01,io+1); /* LD1 is Parallel Port */
      outb(0x30,io);
      cr30=inb(io+1);
      outb(0x60,io);
      cr60=inb(io+1);
      outb(0x61,io);
      cr61=inb(io+1);
      outb(0x70,io);
      cr70=inb(io+1);
      outb(0x74,io);
      cr74=inb(io+1);
      outb(0xf0,io);
      crf0=inb(io+1);
      outb(0xaa,io);

      if (verbose_probing) {
            printk(KERN_INFO "Winbond LPT Config: cr_30=%02x 60,61=%02x%02x "
                   "70=%02x 74=%02x, f0=%02x\n", cr30,cr60,cr61,cr70,cr74,crf0);
            printk(KERN_INFO "Winbond LPT Config: active=%s, io=0x%02x%02x irq=%d, ", 
                   (cr30 & 0x01) ? "yes":"no", cr60,cr61,cr70&0x0f );
            if ((cr74 & 0x07) > 3)
                  printk("dma=none\n");
            else
                  printk("dma=%d\n",cr74 & 0x07);
            printk(KERN_INFO "Winbond LPT Config: irqtype=%s, ECP fifo threshold=%d\n",
                   irqtypes[crf0>>7], (crf0>>3)&0x0f);
            printk(KERN_INFO "Winbond LPT Config: Port mode=%s\n", modes[crf0 & 0x07]);
      }

      if(cr30 & 0x01) { /* the settings can be interrogated later ... */
            while((superios[i].io!= 0) && (i<NR_SUPERIOS))
                  i++;
            if(i==NR_SUPERIOS) 
                  printk(KERN_INFO "Super-IO: too many chips!\n");
            else {
                  superios[i].io = (cr60<<8)|cr61;
                  superios[i].irq = cr70&0x0f;
                  superios[i].dma = (((cr74 & 0x07) > 3) ?
                                 PARPORT_DMA_NONE : (cr74 & 0x07));
            }
      }
}

static void __devinit decode_winbond(int efer, int key, int devid, int devrev, int oldid)
{
      const char *type = "unknown";
      int id,progif=2;

      if (devid == devrev)
            /* simple heuristics, we happened to read some
                   non-winbond register */
            return;

      id=(devid<<8) | devrev;

      /* Values are from public data sheets pdf files, I can just
           confirm 83977TF is correct :-) */
      if      (id == 0x9771) type="83977F/AF";
      else if (id == 0x9773) type="83977TF / SMSC 97w33x/97w34x";
      else if (id == 0x9774) type="83977ATF";
      else if ((id & ~0x0f) == 0x5270) type="83977CTF / SMSC 97w36x";
      else if ((id & ~0x0f) == 0x52f0) type="83977EF / SMSC 97w35x";
      else if ((id & ~0x0f) == 0x5210) type="83627";
      else if ((id & ~0x0f) == 0x6010) type="83697HF";
      else if ((oldid &0x0f ) == 0x0a) { type="83877F"; progif=1;}
      else if ((oldid &0x0f ) == 0x0b) { type="83877AF"; progif=1;}
      else if ((oldid &0x0f ) == 0x0c) { type="83877TF"; progif=1;}
      else if ((oldid &0x0f ) == 0x0d) { type="83877ATF"; progif=1;}
      else progif=0;

      if (verbose_probing)
            printk(KERN_INFO "Winbond chip at EFER=0x%x key=0x%02x "
                   "devid=%02x devrev=%02x oldid=%02x type=%s\n", 
                   efer, key, devid, devrev, oldid, type);

      if (progif == 2)
            show_parconfig_winbond(efer,key);
}

static void __devinit decode_smsc(int efer, int key, int devid, int devrev)
{
        const char *type = "unknown";
      void (*func)(int io, int key);
        int id;

        if (devid == devrev)
            /* simple heuristics, we happened to read some
                   non-smsc register */
            return;

      func=NULL;
        id=(devid<<8) | devrev;

      if    (id==0x0302) {type="37c669"; func=show_parconfig_smsc37c669;}
      else if     (id==0x6582) type="37c665IR";
      else if     (devid==0x65) type="37c665GT";
      else if     (devid==0x66) type="37c666GT";

      if (verbose_probing)
            printk(KERN_INFO "SMSC chip at EFER=0x%x "
                   "key=0x%02x devid=%02x devrev=%02x type=%s\n",
                   efer, key, devid, devrev, type);

      if (func)
            func(efer,key);
}


static void __devinit winbond_check(int io, int key)
{
      int devid,devrev,oldid,x_devid,x_devrev,x_oldid;

      if (!request_region(io, 3, __FUNCTION__))
            return;

      /* First probe without key */
      outb(0x20,io);
      x_devid=inb(io+1);
      outb(0x21,io);
      x_devrev=inb(io+1);
      outb(0x09,io);
      x_oldid=inb(io+1);

      outb(key,io);
      outb(key,io);     /* Write Magic Sequence to EFER, extended
                             funtion enable register */
      outb(0x20,io);    /* Write EFIR, extended function index register */
      devid=inb(io+1);  /* Read EFDR, extended function data register */
      outb(0x21,io);
      devrev=inb(io+1);
      outb(0x09,io);
      oldid=inb(io+1);
      outb(0xaa,io);    /* Magic Seal */

      if ((x_devid == devid) && (x_devrev == devrev) && (x_oldid == oldid))
            goto out; /* protection against false positives */

      decode_winbond(io,key,devid,devrev,oldid);
out:
      release_region(io, 3);
}

static void __devinit winbond_check2(int io,int key)
{
        int devid,devrev,oldid,x_devid,x_devrev,x_oldid;

      if (!request_region(io, 3, __FUNCTION__))
            return;

      /* First probe without the key */
      outb(0x20,io+2);
      x_devid=inb(io+2);
      outb(0x21,io+1);
      x_devrev=inb(io+2);
      outb(0x09,io+1);
      x_oldid=inb(io+2);

        outb(key,io);     /* Write Magic Byte to EFER, extended
                             funtion enable register */
        outb(0x20,io+2);  /* Write EFIR, extended function index register */
        devid=inb(io+2);  /* Read EFDR, extended function data register */
        outb(0x21,io+1);
        devrev=inb(io+2);
        outb(0x09,io+1);
        oldid=inb(io+2);
        outb(0xaa,io);    /* Magic Seal */

      if ((x_devid == devid) && (x_devrev == devrev) && (x_oldid == oldid))
            goto out; /* protection against false positives */

      decode_winbond(io,key,devid,devrev,oldid);
out:
      release_region(io, 3);
}

static void __devinit smsc_check(int io, int key)
{
        int id,rev,oldid,oldrev,x_id,x_rev,x_oldid,x_oldrev;

      if (!request_region(io, 3, __FUNCTION__))
            return;

      /* First probe without the key */
      outb(0x0d,io);
      x_oldid=inb(io+1);
      outb(0x0e,io);
      x_oldrev=inb(io+1);
      outb(0x20,io);
      x_id=inb(io+1);
      outb(0x21,io);
      x_rev=inb(io+1);

        outb(key,io);
        outb(key,io);     /* Write Magic Sequence to EFER, extended
                             funtion enable register */
        outb(0x0d,io);    /* Write EFIR, extended function index register */
        oldid=inb(io+1);  /* Read EFDR, extended function data register */
        outb(0x0e,io);
        oldrev=inb(io+1);
      outb(0x20,io);
      id=inb(io+1);
      outb(0x21,io);
      rev=inb(io+1);
        outb(0xaa,io);    /* Magic Seal */

      if ((x_id == id) && (x_oldrev == oldrev) &&
          (x_oldid == oldid) && (x_rev == rev))
            goto out; /* protection against false positives */

        decode_smsc(io,key,oldid,oldrev);
out:
      release_region(io, 3);
}


static void __devinit detect_and_report_winbond (void)
{ 
      if (verbose_probing)
            printk(KERN_DEBUG "Winbond Super-IO detection, now testing ports 3F0,370,250,4E,2E ...\n");
      winbond_check(0x3f0,0x87);
      winbond_check(0x370,0x87);
      winbond_check(0x2e ,0x87);
      winbond_check(0x4e ,0x87);
      winbond_check(0x3f0,0x86);
      winbond_check2(0x250,0x88); 
      winbond_check2(0x250,0x89);
}

static void __devinit detect_and_report_smsc (void)
{
      if (verbose_probing)
            printk(KERN_DEBUG "SMSC Super-IO detection, now testing Ports 2F0, 370 ...\n");
      smsc_check(0x3f0,0x55);
      smsc_check(0x370,0x55);
      smsc_check(0x3f0,0x44);
      smsc_check(0x370,0x44);
}
#endif /* CONFIG_PARPORT_PC_SUPERIO */

static int get_superio_dma (struct parport *p)
{
      int i=0;
      while( (superios[i].io != p->base) && (i<NR_SUPERIOS))
            i++;
      if (i!=NR_SUPERIOS)
            return superios[i].dma;
      return PARPORT_DMA_NONE;
}

static int get_superio_irq (struct parport *p)
{
      int i=0;
        while( (superios[i].io != p->base) && (i<NR_SUPERIOS))
                i++;
        if (i!=NR_SUPERIOS)
                return superios[i].irq;
        return PARPORT_IRQ_NONE;
}
      

/* --- Mode detection ------------------------------------- */

/*
 * Checks for port existence, all ports support SPP MODE
 * Returns: 
 *         0           :  No parallel port at this address
 *  PARPORT_MODE_PCSPP :  SPP port detected 
 *                        (if the user specified an ioport himself,
 *                         this shall always be the case!)
 *
 */
static int parport_SPP_supported(struct parport *pb)
{
      unsigned char r, w;

      /*
       * first clear an eventually pending EPP timeout 
       * I (sailer@ife.ee.ethz.ch) have an SMSC chipset
       * that does not even respond to SPP cycles if an EPP
       * timeout is pending
       */
      clear_epp_timeout(pb);

      /* Do a simple read-write test to make sure the port exists. */
      w = 0xc;
      outb (w, CONTROL (pb));

      /* Is there a control register that we can read from?  Some
       * ports don't allow reads, so read_control just returns a
       * software copy. Some ports _do_ allow reads, so bypass the
       * software copy here.  In addition, some bits aren't
       * writable. */
      r = inb (CONTROL (pb));
      if ((r & 0xf) == w) {
            w = 0xe;
            outb (w, CONTROL (pb));
            r = inb (CONTROL (pb));
            outb (0xc, CONTROL (pb));
            if ((r & 0xf) == w)
                  return PARPORT_MODE_PCSPP;
      }

      if (user_specified)
            /* That didn't work, but the user thinks there's a
             * port here. */
            printk (KERN_INFO "parport 0x%lx (WARNING): CTR: "
                  "wrote 0x%02x, read 0x%02x\n", pb->base, w, r);

      /* Try the data register.  The data lines aren't tri-stated at
       * this stage, so we expect back what we wrote. */
      w = 0xaa;
      parport_pc_write_data (pb, w);
      r = parport_pc_read_data (pb);
      if (r == w) {
            w = 0x55;
            parport_pc_write_data (pb, w);
            r = parport_pc_read_data (pb);
            if (r == w)
                  return PARPORT_MODE_PCSPP;
      }

      if (user_specified) {
            /* Didn't work, but the user is convinced this is the
             * place. */
            printk (KERN_INFO "parport 0x%lx (WARNING): DATA: "
                  "wrote 0x%02x, read 0x%02x\n", pb->base, w, r);
            printk (KERN_INFO "parport 0x%lx: You gave this address, "
                  "but there is probably no parallel port there!\n",
                  pb->base);
      }

      /* It's possible that we can't read the control register or
       * the data register.  In that case just believe the user. */
      if (user_specified)
            return PARPORT_MODE_PCSPP;

      return 0;
}

/* Check for ECR
 *
 * Old style XT ports alias io ports every 0x400, hence accessing ECR
 * on these cards actually accesses the CTR.
 *
 * Modern cards don't do this but reading from ECR will return 0xff
 * regardless of what is written here if the card does NOT support
 * ECP.
 *
 * We first check to see if ECR is the same as CTR.  If not, the low
 * two bits of ECR aren't writable, so we check by writing ECR and
 * reading it back to see if it's what we expect.
 */
static int parport_ECR_present(struct parport *pb)
{
      struct parport_pc_private *priv = pb->private_data;
      unsigned char r = 0xc;

      outb (r, CONTROL (pb));
      if ((inb (ECONTROL (pb)) & 0x3) == (r & 0x3)) {
            outb (r ^ 0x2, CONTROL (pb)); /* Toggle bit 1 */

            r = inb (CONTROL (pb));
            if ((inb (ECONTROL (pb)) & 0x2) == (r & 0x2))
                  goto no_reg; /* Sure that no ECR register exists */
      }
      
      if ((inb (ECONTROL (pb)) & 0x3 ) != 0x1)
            goto no_reg;

      ECR_WRITE (pb, 0x34);
      if (inb (ECONTROL (pb)) != 0x35)
            goto no_reg;

      priv->ecr = 1;
      outb (0xc, CONTROL (pb));
      
      /* Go to mode 000 */
      frob_set_mode (pb, ECR_SPP);

      return 1;

 no_reg:
      outb (0xc, CONTROL (pb));
      return 0; 
}

#ifdef CONFIG_PARPORT_1284
/* Detect PS/2 support.
 *
 * Bit 5 (0x20) sets the PS/2 data direction; setting this high
 * allows us to read data from the data lines.  In theory we would get back
 * 0xff but any peripheral attached to the port may drag some or all of the
 * lines down to zero.  So if we get back anything that isn't the contents
 * of the data register we deem PS/2 support to be present. 
 *
 * Some SPP ports have "half PS/2" ability - you can't turn off the line
 * drivers, but an external peripheral with sufficiently beefy drivers of
 * its own can overpower them and assert its own levels onto the bus, from
 * where they can then be read back as normal.  Ports with this property
 * and the right type of device attached are likely to fail the SPP test,
 * (as they will appear to have stuck bits) and so the fact that they might
 * be misdetected here is rather academic. 
 */

static int parport_PS2_supported(struct parport *pb)
{
      int ok = 0;
  
      clear_epp_timeout(pb);

      /* try to tri-state the buffer */
      parport_pc_data_reverse (pb);
      
      parport_pc_write_data(pb, 0x55);
      if (parport_pc_read_data(pb) != 0x55) ok++;

      parport_pc_write_data(pb, 0xaa);
      if (parport_pc_read_data(pb) != 0xaa) ok++;

      /* cancel input mode */
      parport_pc_data_forward (pb);

      if (ok) {
            pb->modes |= PARPORT_MODE_TRISTATE;
      } else {
            struct parport_pc_private *priv = pb->private_data;
            priv->ctr_writable &= ~0x20;
      }

      return ok;
}

#ifdef CONFIG_PARPORT_PC_FIFO
static int __devinit parport_ECP_supported(struct parport *pb)
{
      int i;
      int config, configb;
      int pword;
      struct parport_pc_private *priv = pb->private_data;
      /* Translate ECP intrLine to ISA irq value */   
      static const int intrline[]= { 0, 7, 9, 10, 11, 14, 15, 5 }; 

      /* If there is no ECR, we have no hope of supporting ECP. */
      if (!priv->ecr)
            return 0;

      /* Find out FIFO depth */
      ECR_WRITE (pb, ECR_SPP << 5); /* Reset FIFO */
      ECR_WRITE (pb, ECR_TST << 5); /* TEST FIFO */
      for (i=0; i < 1024 && !(inb (ECONTROL (pb)) & 0x02); i++)
            outb (0xaa, FIFO (pb));

      /*
       * Using LGS chipset it uses ECR register, but
       * it doesn't support ECP or FIFO MODE
       */
      if (i == 1024) {
            ECR_WRITE (pb, ECR_SPP << 5);
            return 0;
      }

      priv->fifo_depth = i;
      if (verbose_probing)
            printk (KERN_DEBUG "0x%lx: FIFO is %d bytes\n", pb->base, i);

      /* Find out writeIntrThreshold */
      frob_econtrol (pb, 1<<2, 1<<2);
      frob_econtrol (pb, 1<<2, 0);
      for (i = 1; i <= priv->fifo_depth; i++) {
            inb (FIFO (pb));
            udelay (50);
            if (inb (ECONTROL (pb)) & (1<<2))
                  break;
      }

      if (i <= priv->fifo_depth) {
            if (verbose_probing)
                  printk (KERN_DEBUG "0x%lx: writeIntrThreshold is %d\n",
                        pb->base, i);
      } else
            /* Number of bytes we know we can write if we get an
                   interrupt. */
            i = 0;

      priv->writeIntrThreshold = i;

      /* Find out readIntrThreshold */
      frob_set_mode (pb, ECR_PS2); /* Reset FIFO and enable PS2 */
      parport_pc_data_reverse (pb); /* Must be in PS2 mode */
      frob_set_mode (pb, ECR_TST); /* Test FIFO */
      frob_econtrol (pb, 1<<2, 1<<2);
      frob_econtrol (pb, 1<<2, 0);
      for (i = 1; i <= priv->fifo_depth; i++) {
            outb (0xaa, FIFO (pb));
            if (inb (ECONTROL (pb)) & (1<<2))
                  break;
      }

      if (i <= priv->fifo_depth) {
            if (verbose_probing)
                  printk (KERN_INFO "0x%lx: readIntrThreshold is %d\n",
                        pb->base, i);
      } else
            /* Number of bytes we can read if we get an interrupt. */
            i = 0;

      priv->readIntrThreshold = i;

      ECR_WRITE (pb, ECR_SPP << 5); /* Reset FIFO */
      ECR_WRITE (pb, 0xf4); /* Configuration mode */
      config = inb (CONFIGA (pb));
      pword = (config >> 4) & 0x7;
      switch (pword) {
      case 0:
            pword = 2;
            printk (KERN_WARNING "0x%lx: Unsupported pword size!\n",
                  pb->base);
            break;
      case 2:
            pword = 4;
            printk (KERN_WARNING "0x%lx: Unsupported pword size!\n",
                  pb->base);
            break;
      default:
            printk (KERN_WARNING "0x%lx: Unknown implementation ID\n",
                  pb->base);
            /* Assume 1 */
      case 1:
            pword = 1;
      }
      priv->pword = pword;

      if (verbose_probing) {
            printk (KERN_DEBUG "0x%lx: PWord is %d bits\n", pb->base, 8 * pword);
            
            printk (KERN_DEBUG "0x%lx: Interrupts are ISA-%s\n", pb->base,
                  config & 0x80 ? "Level" : "Pulses");

            configb = inb (CONFIGB (pb));
            printk (KERN_DEBUG "0x%lx: ECP port cfgA=0x%02x cfgB=0x%02x\n",
                  pb->base, config, configb);
            printk (KERN_DEBUG "0x%lx: ECP settings irq=", pb->base);
            if ((configb >>3) & 0x07)
                  printk("%d",intrline[(configb >>3) & 0x07]);
            else
                  printk("<none or set by other means>");
            printk (" dma=");
            if( (configb & 0x03 ) == 0x00)
                  printk("<none or set by other means>\n");
            else
                  printk("%d\n",configb & 0x07);
      }

      /* Go back to mode 000 */
      frob_set_mode (pb, ECR_SPP);

      return 1;
}
#endif

static int parport_ECPPS2_supported(struct parport *pb)
{
      const struct parport_pc_private *priv = pb->private_data;
      int result;
      unsigned char oecr;

      if (!priv->ecr)
            return 0;

      oecr = inb (ECONTROL (pb));
      ECR_WRITE (pb, ECR_PS2 << 5);
      result = parport_PS2_supported(pb);
      ECR_WRITE (pb, oecr);
      return result;
}

/* EPP mode detection  */

static int parport_EPP_supported(struct parport *pb)
{
      const struct parport_pc_private *priv = pb->private_data;

      /*
       * Theory:
       *    Bit 0 of STR is the EPP timeout bit, this bit is 0
       *    when EPP is possible and is set high when an EPP timeout
       *    occurs (EPP uses the HALT line to stop the CPU while it does
       *    the byte transfer, an EPP timeout occurs if the attached
       *    device fails to respond after 10 micro seconds).
       *
       *    This bit is cleared by either reading it (National Semi)
       *    or writing a 1 to the bit (SMC, UMC, WinBond), others ???
       *    This bit is always high in non EPP modes.
       */

      /* If EPP timeout bit clear then EPP available */
      if (!clear_epp_timeout(pb)) {
            return 0;  /* No way to clear timeout */
      }

      /* Check for Intel bug. */
      if (priv->ecr) {
            unsigned char i;
            for (i = 0x00; i < 0x80; i += 0x20) {
                  ECR_WRITE (pb, i);
                  if (clear_epp_timeout (pb)) {
                        /* Phony EPP in ECP. */
                        return 0;
                  }
            }
      }

      pb->modes |= PARPORT_MODE_EPP;

      /* Set up access functions to use EPP hardware. */
      pb->ops->epp_read_data = parport_pc_epp_read_data;
      pb->ops->epp_write_data = parport_pc_epp_write_data;
      pb->ops->epp_read_addr = parport_pc_epp_read_addr;
      pb->ops->epp_write_addr = parport_pc_epp_write_addr;

      return 1;
}

static int parport_ECPEPP_supported(struct parport *pb)
{
      struct parport_pc_private *priv = pb->private_data;
      int result;
      unsigned char oecr;

      if (!priv->ecr) {
            return 0;
      }

      oecr = inb (ECONTROL (pb));
      /* Search for SMC style EPP+ECP mode */
      ECR_WRITE (pb, 0x80);
      outb (0x04, CONTROL (pb));
      result = parport_EPP_supported(pb);

      ECR_WRITE (pb, oecr);

      if (result) {
            /* Set up access functions to use ECP+EPP hardware. */
            pb->ops->epp_read_data = parport_pc_ecpepp_read_data;
            pb->ops->epp_write_data = parport_pc_ecpepp_write_data;
            pb->ops->epp_read_addr = parport_pc_ecpepp_read_addr;
            pb->ops->epp_write_addr = parport_pc_ecpepp_write_addr;
      }

      return result;
}

#else /* No IEEE 1284 support */

/* Don't bother probing for modes we know we won't use. */
static int __devinit parport_PS2_supported(struct parport *pb) { return 0; }
#ifdef CONFIG_PARPORT_PC_FIFO
static int __devinit parport_ECP_supported(struct parport *pb) { return 0; }
#endif
static int __devinit parport_EPP_supported(struct parport *pb) { return 0; }
static int __devinit parport_ECPEPP_supported(struct parport *pb){return 0;}
static int __devinit parport_ECPPS2_supported(struct parport *pb){return 0;}

#endif /* No IEEE 1284 support */

/* --- IRQ detection -------------------------------------- */

/* Only if supports ECP mode */
static int programmable_irq_support(struct parport *pb)
{
      int irq, intrLine;
      unsigned char oecr = inb (ECONTROL (pb));
      static const int lookup[8] = {
            PARPORT_IRQ_NONE, 7, 9, 10, 11, 14, 15, 5
      };

      ECR_WRITE (pb, ECR_CNF << 5); /* Configuration MODE */

      intrLine = (inb (CONFIGB (pb)) >> 3) & 0x07;
      irq = lookup[intrLine];

      ECR_WRITE (pb, oecr);
      return irq;
}

static int irq_probe_ECP(struct parport *pb)
{
      int i;
      unsigned long irqs;

      irqs = probe_irq_on();
            
      ECR_WRITE (pb, ECR_SPP << 5); /* Reset FIFO */
      ECR_WRITE (pb, (ECR_TST << 5) | 0x04);
      ECR_WRITE (pb, ECR_TST << 5);

      /* If Full FIFO sure that writeIntrThreshold is generated */
      for (i=0; i < 1024 && !(inb (ECONTROL (pb)) & 0x02) ; i++) 
            outb (0xaa, FIFO (pb));
            
      pb->irq = probe_irq_off(irqs);
      ECR_WRITE (pb, ECR_SPP << 5);

      if (pb->irq <= 0)
            pb->irq = PARPORT_IRQ_NONE;

      return pb->irq;
}

/*
 * This detection seems that only works in National Semiconductors
 * This doesn't work in SMC, LGS, and Winbond 
 */
static int irq_probe_EPP(struct parport *pb)
{
#ifndef ADVANCED_DETECT
      return PARPORT_IRQ_NONE;
#else
      int irqs;
      unsigned char oecr;

      if (pb->modes & PARPORT_MODE_PCECR)
            oecr = inb (ECONTROL (pb));

      irqs = probe_irq_on();

      if (pb->modes & PARPORT_MODE_PCECR)
            frob_econtrol (pb, 0x10, 0x10);
      
      clear_epp_timeout(pb);
      parport_pc_frob_control (pb, 0x20, 0x20);
      parport_pc_frob_control (pb, 0x10, 0x10);
      clear_epp_timeout(pb);

      /* Device isn't expecting an EPP read
       * and generates an IRQ.
       */
      parport_pc_read_epp(pb);
      udelay(20);

      pb->irq = probe_irq_off (irqs);
      if (pb->modes & PARPORT_MODE_PCECR)
            ECR_WRITE (pb, oecr);
      parport_pc_write_control(pb, 0xc);

      if (pb->irq <= 0)
            pb->irq = PARPORT_IRQ_NONE;

      return pb->irq;
#endif /* Advanced detection */
}

static int irq_probe_SPP(struct parport *pb)
{
      /* Don't even try to do this. */
      return PARPORT_IRQ_NONE;
}

/* We will attempt to share interrupt requests since other devices
 * such as sound cards and network cards seem to like using the
 * printer IRQs.
 *
 * When ECP is available we can autoprobe for IRQs.
 * NOTE: If we can autoprobe it, we can register the IRQ.
 */
static int parport_irq_probe(struct parport *pb)
{
      struct parport_pc_private *priv = pb->private_data;

      if (priv->ecr) {
            pb->irq = programmable_irq_support(pb);

            if (pb->irq == PARPORT_IRQ_NONE)
                  pb->irq = irq_probe_ECP(pb);
      }

      if ((pb->irq == PARPORT_IRQ_NONE) && priv->ecr &&
          (pb->modes & PARPORT_MODE_EPP))
            pb->irq = irq_probe_EPP(pb);

      clear_epp_timeout(pb);

      if (pb->irq == PARPORT_IRQ_NONE && (pb->modes & PARPORT_MODE_EPP))
            pb->irq = irq_probe_EPP(pb);

      clear_epp_timeout(pb);

      if (pb->irq == PARPORT_IRQ_NONE)
            pb->irq = irq_probe_SPP(pb);

      if (pb->irq == PARPORT_IRQ_NONE)
            pb->irq = get_superio_irq(pb);

      return pb->irq;
}

/* --- DMA detection -------------------------------------- */

/* Only if chipset conforms to ECP ISA Interface Standard */
static int programmable_dma_support (struct parport *p)
{
      unsigned char oecr = inb (ECONTROL (p));
      int dma;

      frob_set_mode (p, ECR_CNF);
      
      dma = inb (CONFIGB(p)) & 0x07;
      /* 000: Indicates jumpered 8-bit DMA if read-only.
         100: Indicates jumpered 16-bit DMA if read-only. */
      if ((dma & 0x03) == 0)
            dma = PARPORT_DMA_NONE;

      ECR_WRITE (p, oecr);
      return dma;
}

static int parport_dma_probe (struct parport *p)
{
      const struct parport_pc_private *priv = p->private_data;
      if (priv->ecr)
            p->dma = programmable_dma_support(p); /* ask ECP chipset first */
      if (p->dma == PARPORT_DMA_NONE) {
            /* ask known Super-IO chips proper, although these
               claim ECP compatible, some don't report their DMA
               conforming to ECP standards */
            p->dma = get_superio_dma(p);
      }

      return p->dma;
}

/* --- Initialisation code -------------------------------- */

static LIST_HEAD(ports_list);
static DEFINE_SPINLOCK(ports_lock);

struct parport *parport_pc_probe_port (unsigned long int base,
                               unsigned long int base_hi,
                               int irq, int dma,
                               struct device *dev)
{
      struct parport_pc_private *priv;
      struct parport_operations *ops;
      struct parport *p;
      int probedirq = PARPORT_IRQ_NONE;
      struct resource *base_res;
      struct resource   *ECR_res = NULL;
      struct resource   *EPP_res = NULL;
      struct platform_device *pdev = NULL;

      if (!dev) {
            /* We need a physical device to attach to, but none was
             * provided. Create our own. */
            pdev = platform_device_register_simple("parport_pc",
                                           base, NULL, 0);
            if (IS_ERR(pdev))
                  return NULL;
            dev = &pdev->dev;
      }

      ops = kmalloc(sizeof (struct parport_operations), GFP_KERNEL);
      if (!ops)
            goto out1;

      priv = kmalloc (sizeof (struct parport_pc_private), GFP_KERNEL);
      if (!priv)
            goto out2;

      /* a misnomer, actually - it's allocate and reserve parport number */
      p = parport_register_port(base, irq, dma, ops);
      if (!p)
            goto out3;

      base_res = request_region(base, 3, p->name);
      if (!base_res)
            goto out4;

      memcpy(ops, &parport_pc_ops, sizeof (struct parport_operations));
      priv->ctr = 0xc;
      priv->ctr_writable = ~0x10;
      priv->ecr = 0;
      priv->fifo_depth = 0;
      priv->dma_buf = NULL;
      priv->dma_handle = 0;
      INIT_LIST_HEAD(&priv->list);
      priv->port = p;

      p->dev = dev;
      p->base_hi = base_hi;
      p->modes = PARPORT_MODE_PCSPP | PARPORT_MODE_SAFEININT;
      p->private_data = priv;

      if (base_hi) {
            ECR_res = request_region(base_hi, 3, p->name);
            if (ECR_res)
                  parport_ECR_present(p);
      }

      if (base != 0x3bc) {
            EPP_res = request_region(base+0x3, 5, p->name);
            if (EPP_res)
                  if (!parport_EPP_supported(p))
                        parport_ECPEPP_supported(p);
      }
      if (!parport_SPP_supported (p))
            /* No port. */
            goto out5;
      if (priv->ecr)
            parport_ECPPS2_supported(p);
      else
            parport_PS2_supported(p);

      p->size = (p->modes & PARPORT_MODE_EPP)?8:3;

      printk(KERN_INFO "%s: PC-style at 0x%lx", p->name, p->base);
      if (p->base_hi && priv->ecr)
            printk(" (0x%lx)", p->base_hi);
      if (p->irq == PARPORT_IRQ_AUTO) {
            p->irq = PARPORT_IRQ_NONE;
            parport_irq_probe(p);
      } else if (p->irq == PARPORT_IRQ_PROBEONLY) {
            p->irq = PARPORT_IRQ_NONE;
            parport_irq_probe(p);
            probedirq = p->irq;
            p->irq = PARPORT_IRQ_NONE;
      }
      if (p->irq != PARPORT_IRQ_NONE) {
            printk(", irq %d", p->irq);
            priv->ctr_writable |= 0x10;

            if (p->dma == PARPORT_DMA_AUTO) {
                  p->dma = PARPORT_DMA_NONE;
                  parport_dma_probe(p);
            }
      }
      if (p->dma == PARPORT_DMA_AUTO) /* To use DMA, giving the irq
                                           is mandatory (see above) */
            p->dma = PARPORT_DMA_NONE;

#ifdef CONFIG_PARPORT_PC_FIFO
      if (parport_ECP_supported(p) &&
          p->dma != PARPORT_DMA_NOFIFO &&
          priv->fifo_depth > 0 && p->irq != PARPORT_IRQ_NONE) {
            p->modes |= PARPORT_MODE_ECP | PARPORT_MODE_COMPAT;
            p->ops->compat_write_data = parport_pc_compat_write_block_pio;
#ifdef CONFIG_PARPORT_1284
            p->ops->ecp_write_data = parport_pc_ecp_write_block_pio;
            /* currently broken, but working on it.. (FB) */
            /* p->ops->ecp_read_data = parport_pc_ecp_read_block_pio; */
#endif /* IEEE 1284 support */
            if (p->dma != PARPORT_DMA_NONE) {
                  printk(", dma %d", p->dma);
                  p->modes |= PARPORT_MODE_DMA;
            }
            else printk(", using FIFO");
      }
      else
            /* We can't use the DMA channel after all. */
            p->dma = PARPORT_DMA_NONE;
#endif /* Allowed to use FIFO/DMA */

      printk(" [");
#define printmode(x) {if(p->modes&PARPORT_MODE_##x){printk("%s%s",f?",":"",#x);f++;}}
      {
            int f = 0;
            printmode(PCSPP);
            printmode(TRISTATE);
            printmode(COMPAT)
            printmode(EPP);
            printmode(ECP);
            printmode(DMA);
      }
#undef printmode
#ifndef CONFIG_PARPORT_1284
      printk ("(,...)");
#endif /* CONFIG_PARPORT_1284 */
      printk("]\n");
      if (probedirq != PARPORT_IRQ_NONE) 
            printk(KERN_INFO "%s: irq %d detected\n", p->name, probedirq);

      /* If No ECP release the ports grabbed above. */
      if (ECR_res && (p->modes & PARPORT_MODE_ECP) == 0) {
            release_region(base_hi, 3);
            ECR_res = NULL;
      }
      /* Likewise for EEP ports */
      if (EPP_res && (p->modes & PARPORT_MODE_EPP) == 0) {
            release_region(base+3, 5);
            EPP_res = NULL;
      }
      if (p->irq != PARPORT_IRQ_NONE) {
            if (request_irq (p->irq, parport_irq_handler,
                         0, p->name, p)) {
                  printk (KERN_WARNING "%s: irq %d in use, "
                        "resorting to polled operation\n",
                        p->name, p->irq);
                  p->irq = PARPORT_IRQ_NONE;
                  p->dma = PARPORT_DMA_NONE;
            }

#ifdef CONFIG_PARPORT_PC_FIFO
#ifdef HAS_DMA
            if (p->dma != PARPORT_DMA_NONE) {
                  if (request_dma (p->dma, p->name)) {
                        printk (KERN_WARNING "%s: dma %d in use, "
                              "resorting to PIO operation\n",
                              p->name, p->dma);
                        p->dma = PARPORT_DMA_NONE;
                  } else {
                        priv->dma_buf =
                          dma_alloc_coherent(dev,
                                           PAGE_SIZE,
                                           &priv->dma_handle,
                                           GFP_KERNEL);
                        if (! priv->dma_buf) {
                              printk (KERN_WARNING "%s: "
                                    "cannot get buffer for DMA, "
                                    "resorting to PIO operation\n",
                                    p->name);
                              free_dma(p->dma);
                              p->dma = PARPORT_DMA_NONE;
                        }
                  }
            }
#endif
#endif
      }

      /* Done probing.  Now put the port into a sensible start-up state. */
      if (priv->ecr)
            /*
             * Put the ECP detected port in PS2 mode.
             * Do this also for ports that have ECR but don't do ECP.
             */
            ECR_WRITE (p, 0x34);

      parport_pc_write_data(p, 0);
      parport_pc_data_forward (p);

      /* Now that we've told the sharing engine about the port, and
         found out its characteristics, let the high-level drivers
         know about it. */
      spin_lock(&ports_lock);
      list_add(&priv->list, &ports_list);
      spin_unlock(&ports_lock);
      parport_announce_port (p);

      return p;

out5:
      if (ECR_res)
            release_region(base_hi, 3);
      if (EPP_res)
            release_region(base+0x3, 5);
      release_region(base, 3);
out4:
      parport_put_port(p);
out3:
      kfree (priv);
out2:
      kfree (ops);
out1:
      if (pdev)
            platform_device_unregister(pdev);
      return NULL;
}

EXPORT_SYMBOL (parport_pc_probe_port);

void parport_pc_unregister_port (struct parport *p)
{
      struct parport_pc_private *priv = p->private_data;
      struct parport_operations *ops = p->ops;

      parport_remove_port(p);
      spin_lock(&ports_lock);
      list_del_init(&priv->list);
      spin_unlock(&ports_lock);
#if defined(CONFIG_PARPORT_PC_FIFO) && defined(HAS_DMA)
      if (p->dma != PARPORT_DMA_NONE)
            free_dma(p->dma);
#endif
      if (p->irq != PARPORT_IRQ_NONE)
            free_irq(p->irq, p);
      release_region(p->base, 3);
      if (p->size > 3)
            release_region(p->base + 3, p->size - 3);
      if (p->modes & PARPORT_MODE_ECP)
            release_region(p->base_hi, 3);
#if defined(CONFIG_PARPORT_PC_FIFO) && defined(HAS_DMA)
      if (priv->dma_buf)
            dma_free_coherent(p->physport->dev, PAGE_SIZE,
                            priv->dma_buf,
                            priv->dma_handle);
#endif
      kfree (p->private_data);
      parport_put_port(p);
      kfree (ops); /* hope no-one cached it */
}

EXPORT_SYMBOL (parport_pc_unregister_port);

#ifdef CONFIG_PCI

/* ITE support maintained by Rich Liu <richliu@poorman.org> */
static int __devinit sio_ite_8872_probe (struct pci_dev *pdev, int autoirq,
                               int autodma,
                               const struct parport_pc_via_data *via)
{
      short inta_addr[6] = { 0x2A0, 0x2C0, 0x220, 0x240, 0x1E0 };
      struct resource *base_res;
      u32 ite8872set;
      u32 ite8872_lpt, ite8872_lpthi;
      u8 ite8872_irq, type;
      int irq;
      int i;

      DPRINTK (KERN_DEBUG "sio_ite_8872_probe()\n");
      
      // make sure which one chip
      for(i = 0; i < 5; i++) {
            base_res = request_region(inta_addr[i], 32, "it887x");
            if (base_res) {
                  int test;
                  pci_write_config_dword (pdev, 0x60,
                                    0xe5000000 | inta_addr[i]);
                  pci_write_config_dword (pdev, 0x78,
                                    0x00000000 | inta_addr[i]);
                  test = inb (inta_addr[i]);
                  if (test != 0xff) break;
                  release_region(inta_addr[i], 0x8);
            }
      }
      if(i >= 5) {
            printk (KERN_INFO "parport_pc: cannot find ITE8872 INTA\n");
            return 0;
      }

      type = inb (inta_addr[i] + 0x18);
      type &= 0x0f;

      switch (type) {
      case 0x2:
            printk (KERN_INFO "parport_pc: ITE8871 found (1P)\n");
            ite8872set = 0x64200000;
            break;
      case 0xa:
            printk (KERN_INFO "parport_pc: ITE8875 found (1P)\n");
            ite8872set = 0x64200000;
            break;
      case 0xe:
            printk (KERN_INFO "parport_pc: ITE8872 found (2S1P)\n");
            ite8872set = 0x64e00000;
            break;
      case 0x6:
            printk (KERN_INFO "parport_pc: ITE8873 found (1S)\n");
            return 0;
      case 0x8:
            DPRINTK (KERN_DEBUG "parport_pc: ITE8874 found (2S)\n");
            return 0;
      default:
            printk (KERN_INFO "parport_pc: unknown ITE887x\n");
            printk (KERN_INFO "parport_pc: please mail 'lspci -nvv' "
                  "output to Rich.Liu@ite.com.tw\n");
            return 0;
      }

      pci_read_config_byte (pdev, 0x3c, &ite8872_irq);
      pci_read_config_dword (pdev, 0x1c, &ite8872_lpt);
      ite8872_lpt &= 0x0000ff00;
      pci_read_config_dword (pdev, 0x20, &ite8872_lpthi);
      ite8872_lpthi &= 0x0000ff00;
      pci_write_config_dword (pdev, 0x6c, 0xe3000000 | ite8872_lpt);
      pci_write_config_dword (pdev, 0x70, 0xe3000000 | ite8872_lpthi);
      pci_write_config_dword (pdev, 0x80, (ite8872_lpthi<<16) | ite8872_lpt);
      // SET SPP&EPP , Parallel Port NO DMA , Enable All Function
      // SET Parallel IRQ
      pci_write_config_dword (pdev, 0x9c,
                        ite8872set | (ite8872_irq * 0x11111));

      DPRINTK (KERN_DEBUG "ITE887x: The IRQ is %d.\n", ite8872_irq);
      DPRINTK (KERN_DEBUG "ITE887x: The PARALLEL I/O port is 0x%x.\n",
             ite8872_lpt);
      DPRINTK (KERN_DEBUG "ITE887x: The PARALLEL I/O porthi is 0x%x.\n",
             ite8872_lpthi);

      /* Let the user (or defaults) steer us away from interrupts */
      irq = ite8872_irq;
      if (autoirq != PARPORT_IRQ_AUTO)
            irq = PARPORT_IRQ_NONE;

      /*
       * Release the resource so that parport_pc_probe_port can get it.
       */
      release_resource(base_res);
      if (parport_pc_probe_port (ite8872_lpt, ite8872_lpthi,
                           irq, PARPORT_DMA_NONE, &pdev->dev)) {
            printk (KERN_INFO
                  "parport_pc: ITE 8872 parallel port: io=0x%X",
                  ite8872_lpt);
            if (irq != PARPORT_IRQ_NONE)
                  printk (", irq=%d", irq);
            printk ("\n");
            return 1;
      }

      return 0;
}

/* VIA 8231 support by Pavel Fedin <sonic_amiga@rambler.ru>
   based on VIA 686a support code by Jeff Garzik <jgarzik@pobox.com> */
static int __devinitdata parport_init_mode = 0;

/* Data for two known VIA chips */
static struct parport_pc_via_data via_686a_data __devinitdata = {
      0x51,
      0x50,
      0x85,
      0x02,
      0xE2,
      0xF0,
      0xE6
};
static struct parport_pc_via_data via_8231_data __devinitdata = {
      0x45,
      0x44,
      0x50,
      0x04,
      0xF2,
      0xFA,
      0xF6
};

static int __devinit sio_via_probe (struct pci_dev *pdev, int autoirq,
                            int autodma,
                            const struct parport_pc_via_data *via)
{
      u8 tmp, tmp2, siofunc;
      u8 ppcontrol = 0;
      int dma, irq;
      unsigned port1, port2;
      unsigned have_epp = 0;

      printk(KERN_DEBUG "parport_pc: VIA 686A/8231 detected\n");

      switch(parport_init_mode)
      {
      case 1:
          printk(KERN_DEBUG "parport_pc: setting SPP mode\n");
          siofunc = VIA_FUNCTION_PARPORT_SPP;
          break;
      case 2:
          printk(KERN_DEBUG "parport_pc: setting PS/2 mode\n");
          siofunc = VIA_FUNCTION_PARPORT_SPP;
          ppcontrol = VIA_PARPORT_BIDIR;
          break;
      case 3:
          printk(KERN_DEBUG "parport_pc: setting EPP mode\n");
          siofunc = VIA_FUNCTION_PARPORT_EPP;
          ppcontrol = VIA_PARPORT_BIDIR;
          have_epp = 1;
          break;
      case 4:
          printk(KERN_DEBUG "parport_pc: setting ECP mode\n");
          siofunc = VIA_FUNCTION_PARPORT_ECP;
          ppcontrol = VIA_PARPORT_BIDIR;
          break;
      case 5:
          printk(KERN_DEBUG "parport_pc: setting EPP+ECP mode\n");
          siofunc = VIA_FUNCTION_PARPORT_ECP;
          ppcontrol = VIA_PARPORT_BIDIR|VIA_PARPORT_ECPEPP;
          have_epp = 1;
          break;
       default:
          printk(KERN_DEBUG "parport_pc: probing current configuration\n");
          siofunc = VIA_FUNCTION_PROBE;
          break;
      }
      /*
       * unlock super i/o configuration
       */
      pci_read_config_byte(pdev, via->via_pci_superio_config_reg, &tmp);
      tmp |= via->via_pci_superio_config_data;
      pci_write_config_byte(pdev, via->via_pci_superio_config_reg, tmp);

      /* Bits 1-0: Parallel Port Mode / Enable */
      outb(via->viacfg_function, VIA_CONFIG_INDEX);
      tmp = inb (VIA_CONFIG_DATA);
      /* Bit 5: EPP+ECP enable; bit 7: PS/2 bidirectional port enable */
      outb(via->viacfg_parport_control, VIA_CONFIG_INDEX);
      tmp2 = inb (VIA_CONFIG_DATA);
      if (siofunc == VIA_FUNCTION_PROBE)
      {
          siofunc = tmp & VIA_FUNCTION_PARPORT_DISABLE;
          ppcontrol = tmp2;
      }
      else
      {
          tmp &= ~VIA_FUNCTION_PARPORT_DISABLE;
          tmp |= siofunc;
          outb(via->viacfg_function, VIA_CONFIG_INDEX);
          outb(tmp, VIA_CONFIG_DATA);
          tmp2 &= ~(VIA_PARPORT_BIDIR|VIA_PARPORT_ECPEPP);
          tmp2 |= ppcontrol;
          outb(via->viacfg_parport_control, VIA_CONFIG_INDEX);
          outb(tmp2, VIA_CONFIG_DATA);
      }
      
      /* Parallel Port I/O Base Address, bits 9-2 */
      outb(via->viacfg_parport_base, VIA_CONFIG_INDEX);
      port1 = inb(VIA_CONFIG_DATA) << 2;
      
      printk (KERN_DEBUG "parport_pc: Current parallel port base: 0x%X\n",port1);
      if ((port1 == 0x3BC) && have_epp)
      {
          outb(via->viacfg_parport_base, VIA_CONFIG_INDEX);
          outb((0x378 >> 2), VIA_CONFIG_DATA);
          printk(KERN_DEBUG "parport_pc: Parallel port base changed to 0x378\n");
          port1 = 0x378;
      }

      /*
       * lock super i/o configuration
       */
      pci_read_config_byte(pdev, via->via_pci_superio_config_reg, &tmp);
      tmp &= ~via->via_pci_superio_config_data;
      pci_write_config_byte(pdev, via->via_pci_superio_config_reg, tmp);

      if (siofunc == VIA_FUNCTION_PARPORT_DISABLE) {
            printk(KERN_INFO "parport_pc: VIA parallel port disabled in BIOS\n");
            return 0;
      }
      
      /* Bits 7-4: PnP Routing for Parallel Port IRQ */
      pci_read_config_byte(pdev, via->via_pci_parport_irq_reg, &tmp);
      irq = ((tmp & VIA_IRQCONTROL_PARALLEL) >> 4);

      if (siofunc == VIA_FUNCTION_PARPORT_ECP)
      {
          /* Bits 3-2: PnP Routing for Parallel Port DMA */
          pci_read_config_byte(pdev, via->via_pci_parport_dma_reg, &tmp);
          dma = ((tmp & VIA_DMACONTROL_PARALLEL) >> 2);
      }
      else
          /* if ECP not enabled, DMA is not enabled, assumed bogus 'dma' value */
          dma = PARPORT_DMA_NONE;

      /* Let the user (or defaults) steer us away from interrupts and DMA */
      if (autoirq == PARPORT_IRQ_NONE) {
          irq = PARPORT_IRQ_NONE;
          dma = PARPORT_DMA_NONE;
      }
      if (autodma == PARPORT_DMA_NONE)
          dma = PARPORT_DMA_NONE;

      switch (port1) {
      case 0x3bc: port2 = 0x7bc; break;
      case 0x378: port2 = 0x778; break;
      case 0x278: port2 = 0x678; break;
      default:
            printk(KERN_INFO "parport_pc: Weird VIA parport base 0x%X, ignoring\n",
                  port1);
            return 0;
      }

      /* filter bogus IRQs */
      switch (irq) {
      case 0:
      case 2:
      case 8:
      case 13:
            irq = PARPORT_IRQ_NONE;
            break;

      default: /* do nothing */
            break;
      }

      /* finally, do the probe with values obtained */
      if (parport_pc_probe_port (port1, port2, irq, dma, &pdev->dev)) {
            printk (KERN_INFO
                  "parport_pc: VIA parallel port: io=0x%X", port1);
            if (irq != PARPORT_IRQ_NONE)
                  printk (", irq=%d", irq);
            if (dma != PARPORT_DMA_NONE)
                  printk (", dma=%d", dma);
            printk ("\n");
            return 1;
      }
      
      printk(KERN_WARNING "parport_pc: Strange, can't probe VIA parallel port: io=0x%X, irq=%d, dma=%d\n",
            port1, irq, dma);
      return 0;
}


enum parport_pc_sio_types {
      sio_via_686a = 0, /* Via VT82C686A motherboard Super I/O */
      sio_via_8231,           /* Via VT8231 south bridge integrated Super IO */
      sio_ite_8872,
      last_sio
};

/* each element directly indexed from enum list, above */
static struct parport_pc_superio {
      int (*probe) (struct pci_dev *pdev, int autoirq, int autodma,
                  const struct parport_pc_via_data *via);
      const struct parport_pc_via_data *via;
} parport_pc_superio_info[] __devinitdata = {
      { sio_via_probe, &via_686a_data, },
      { sio_via_probe, &via_8231_data, },
      { sio_ite_8872_probe, NULL, },
};

enum parport_pc_pci_cards {
      siig_1p_10x = last_sio,
      siig_2p_10x,
      siig_1p_20x,
      siig_2p_20x,
      lava_parallel,
      lava_parallel_dual_a,
      lava_parallel_dual_b,
      boca_ioppar,
      plx_9050,
      timedia_4078a,
      timedia_4079h,
      timedia_4085h,
      timedia_4088a,
      timedia_4089a,
      timedia_4095a,
      timedia_4096a,
      timedia_4078u,
      timedia_4079a,
      timedia_4085u,
      timedia_4079r,
      timedia_4079s,
      timedia_4079d,
      timedia_4079e,
      timedia_4079f,
      timedia_9079a,
      timedia_9079b,
      timedia_9079c,
      timedia_4006a,
      timedia_4014,
      timedia_4008a,
      timedia_4018,
      timedia_9018a,
      syba_2p_epp,
      syba_1p_ecp,
      titan_010l,
      titan_1284p1,
      titan_1284p2,
      avlab_1p,
      avlab_2p,
      oxsemi_952,
      oxsemi_954,
      oxsemi_840,
      aks_0100,
      mobility_pp,
      netmos_9705,
      netmos_9715,
      netmos_9755,
      netmos_9805,
      netmos_9815,
};


/* each element directly indexed from enum list, above 
 * (but offset by last_sio) */
static struct parport_pc_pci {
      int numports;
      struct { /* BAR (base address registers) numbers in the config
                    space header */
            int lo;
            int hi; /* -1 if not there, >6 for offset-method (max
                           BAR is 6) */
      } addr[4];

      /* If set, this is called immediately after pci_enable_device.
       * If it returns non-zero, no probing will take place and the
       * ports will not be used. */
      int (*preinit_hook) (struct pci_dev *pdev, int autoirq, int autodma);

      /* If set, this is called after probing for ports.  If 'failed'
       * is non-zero we couldn't use any of the ports. */
      void (*postinit_hook) (struct pci_dev *pdev, int failed);
} cards[] = {
      /* siig_1p_10x */       { 1, { { 2, 3 }, } },
      /* siig_2p_10x */       { 2, { { 2, 3 }, { 4, 5 }, } },
      /* siig_1p_20x */       { 1, { { 0, 1 }, } },
      /* siig_2p_20x */       { 2, { { 0, 1 }, { 2, 3 }, } },
      /* lava_parallel */           { 1, { { 0, -1 }, } },
      /* lava_parallel_dual_a */    { 1, { { 0, -1 }, } },
      /* lava_parallel_dual_b */    { 1, { { 0, -1 }, } },
      /* boca_ioppar */       { 1, { { 0, -1 }, } },
      /* plx_9050 */                { 2, { { 4, -1 }, { 5, -1 }, } },
      /* timedia_4078a */           { 1, { { 2, -1 }, } },
      /* timedia_4079h */             { 1, { { 2, 3 }, } },
      /* timedia_4085h */             { 2, { { 2, -1 }, { 4, -1 }, } },
      /* timedia_4088a */             { 2, { { 2, 3 }, { 4, 5 }, } },
      /* timedia_4089a */             { 2, { { 2, 3 }, { 4, 5 }, } },
      /* timedia_4095a */             { 2, { { 2, 3 }, { 4, 5 }, } },
      /* timedia_4096a */             { 2, { { 2, 3 }, { 4, 5 }, } },
      /* timedia_4078u */             { 1, { { 2, -1 }, } },
      /* timedia_4079a */             { 1, { { 2, 3 }, } },
      /* timedia_4085u */             { 2, { { 2, -1 }, { 4, -1 }, } },
      /* timedia_4079r */             { 1, { { 2, 3 }, } },
      /* timedia_4079s */             { 1, { { 2, 3 }, } },
      /* timedia_4079d */             { 1, { { 2, 3 }, } },
      /* timedia_4079e */             { 1, { { 2, 3 }, } },
      /* timedia_4079f */             { 1, { { 2, 3 }, } },
      /* timedia_9079a */             { 1, { { 2, 3 }, } },
      /* timedia_9079b */             { 1, { { 2, 3 }, } },
      /* timedia_9079c */             { 1, { { 2, 3 }, } },
      /* timedia_4006a */             { 1, { { 0, -1 }, } },
      /* timedia_4014  */             { 2, { { 0, -1 }, { 2, -1 }, } },
      /* timedia_4008a */             { 1, { { 0, 1 }, } },
      /* timedia_4018  */             { 2, { { 0, 1 }, { 2, 3 }, } },
      /* timedia_9018a */             { 2, { { 0, 1 }, { 2, 3 }, } },
                              /* SYBA uses fixed offsets in
                                           a 1K io window */
      /* syba_2p_epp AP138B */      { 2, { { 0, 0x078 }, { 0, 0x178 }, } },
      /* syba_1p_ecp W83787 */      { 1, { { 0, 0x078 }, } },
      /* titan_010l */        { 1, { { 3, -1 }, } },
      /* titan_1284p1 */              { 1, { { 0, 1 }, } },
      /* titan_1284p2 */            { 2, { { 0, 1 }, { 2, 3 }, } },
      /* avlab_1p       */    { 1, { { 0, 1}, } },
      /* avlab_2p       */    { 2, { { 0, 1}, { 2, 3 },} },
      /* The Oxford Semi cards are unusual: 954 doesn't support ECP,
       * and 840 locks up if you write 1 to bit 2! */
      /* oxsemi_952 */        { 1, { { 0, 1 }, } },
      /* oxsemi_954 */        { 1, { { 0, -1 }, } },
      /* oxsemi_840 */        { 1, { { 0, -1 }, } },
      /* aks_0100 */                  { 1, { { 0, -1 }, } },
      /* mobility_pp */       { 1, { { 0, 1 }, } },
      /* netmos_9705 */               { 1, { { 0, -1 }, } }, /* untested */
        /* netmos_9715 */               { 2, { { 0, 1 }, { 2, 3 },} }, /* untested */
        /* netmos_9755 */               { 2, { { 0, 1 }, { 2, 3 },} }, /* untested */
      /* netmos_9805 */               { 1, { { 0, -1 }, } }, /* untested */
      /* netmos_9815 */               { 2, { { 0, -1 }, { 2, -1 }, } }, /* untested */
};

static const struct pci_device_id parport_pc_pci_tbl[] = {
      /* Super-IO onboard chips */
      { 0x1106, 0x0686, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sio_via_686a },
      { 0x1106, 0x8231, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sio_via_8231 },
      { PCI_VENDOR_ID_ITE, PCI_DEVICE_ID_ITE_8872,
        PCI_ANY_ID, PCI_ANY_ID, 0, 0, sio_ite_8872 },

      /* PCI cards */
      { PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1P_10x,
        PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_1p_10x },
      { PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2P_10x,
        PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_2p_10x },
      { PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1P_20x,
        PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_1p_20x },
      { PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2P_20x,
        PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_2p_20x },
      { PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_PARALLEL,
        PCI_ANY_ID, PCI_ANY_ID, 0, 0, lava_parallel },
      { PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_DUAL_PAR_A,
        PCI_ANY_ID, PCI_ANY_ID, 0, 0, lava_parallel_dual_a },
      { PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_DUAL_PAR_B,
        PCI_ANY_ID, PCI_ANY_ID, 0, 0, lava_parallel_dual_b },
      { PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_BOCA_IOPPAR,
        PCI_ANY_ID, PCI_ANY_ID, 0, 0, boca_ioppar },
      { PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
        PCI_SUBVENDOR_ID_EXSYS, PCI_SUBDEVICE_ID_EXSYS_4014, 0,0, plx_9050 },
      /* PCI_VENDOR_ID_TIMEDIA/SUNIX has many differing cards ...*/
      { 0x1409, 0x7168, 0x1409, 0x4078, 0, 0, timedia_4078a },
      { 0x1409, 0x7168, 0x1409, 0x4079, 0, 0, timedia_4079h },
      { 0x1409, 0x7168, 0x1409, 0x4085, 0, 0, timedia_4085h },
      { 0x1409, 0x7168, 0x1409, 0x4088, 0, 0, timedia_4088a },
      { 0x1409, 0x7168, 0x1409, 0x4089, 0, 0, timedia_4089a },
      { 0x1409, 0x7168, 0x1409, 0x4095, 0, 0, timedia_4095a },
      { 0x1409, 0x7168, 0x1409, 0x4096, 0, 0, timedia_4096a },
      { 0x1409, 0x7168, 0x1409, 0x5078, 0, 0, timedia_4078u },
      { 0x1409, 0x7168, 0x1409, 0x5079, 0, 0, timedia_4079a },
      { 0x1409, 0x7168, 0x1409, 0x5085, 0, 0, timedia_4085u },
      { 0x1409, 0x7168, 0x1409, 0x6079, 0, 0, timedia_4079r },
      { 0x1409, 0x7168, 0x1409, 0x7079, 0, 0, timedia_4079s },
      { 0x1409, 0x7168, 0x1409, 0x8079, 0, 0, timedia_4079d },
      { 0x1409, 0x7168, 0x1409, 0x9079, 0, 0, timedia_4079e },
      { 0x1409, 0x7168, 0x1409, 0xa079, 0, 0, timedia_4079f },
      { 0x1409, 0x7168, 0x1409, 0xb079, 0, 0, timedia_9079a },
      { 0x1409, 0x7168, 0x1409, 0xc079, 0, 0, timedia_9079b },
      { 0x1409, 0x7168, 0x1409, 0xd079, 0, 0, timedia_9079c },
      { 0x1409, 0x7268, 0x1409, 0x0101, 0, 0, timedia_4006a },
      { 0x1409, 0x7268, 0x1409, 0x0102, 0, 0, timedia_4014 },
      { 0x1409, 0x7268, 0x1409, 0x0103, 0, 0, timedia_4008a },
      { 0x1409, 0x7268, 0x1409, 0x0104, 0, 0, timedia_4018 },
      { 0x1409, 0x7268, 0x1409, 0x9018, 0, 0, timedia_9018a },
      { 0x14f2, 0x0121, PCI_ANY_ID, PCI_ANY_ID, 0, 0, mobility_pp },
      { PCI_VENDOR_ID_SYBA, PCI_DEVICE_ID_SYBA_2P_EPP,
        PCI_ANY_ID, PCI_ANY_ID, 0, 0, syba_2p_epp },
      { PCI_VENDOR_ID_SYBA, PCI_DEVICE_ID_SYBA_1P_ECP,
        PCI_ANY_ID, PCI_ANY_ID, 0, 0, syba_1p_ecp },
      { PCI_VENDOR_ID_TITAN, PCI_DEVICE_ID_TITAN_010L,
        PCI_ANY_ID, PCI_ANY_ID, 0, 0, titan_010l },
      { 0x9710, 0x9805, 0x1000, 0x0010, 0, 0, titan_1284p1 },
      { 0x9710, 0x9815, 0x1000, 0x0020, 0, 0, titan_1284p2 },
      /* PCI_VENDOR_ID_AVLAB/Intek21 has another bunch of cards ...*/
      { 0x14db, 0x2120, PCI_ANY_ID, PCI_ANY_ID, 0, 0, avlab_1p}, /* AFAVLAB_TK9902 */
      { 0x14db, 0x2121, PCI_ANY_ID, PCI_ANY_ID, 0, 0, avlab_2p},
      { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_16PCI952PP,
        PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_952 },
      { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_16PCI954PP,
        PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_954 },
      { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_12PCI840,
        PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_840 },
      { PCI_VENDOR_ID_AKS, PCI_DEVICE_ID_AKS_ALADDINCARD,
        PCI_ANY_ID, PCI_ANY_ID, 0, 0, aks_0100 },
      /* NetMos communication controllers */
      { PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9705,
        PCI_ANY_ID, PCI_ANY_ID, 0, 0, netmos_9705 },
      { PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9715,
        PCI_ANY_ID, PCI_ANY_ID, 0, 0, netmos_9715 },
      { PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9755,
        PCI_ANY_ID, PCI_ANY_ID, 0, 0, netmos_9755 },
      { PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9805,
        PCI_ANY_ID, PCI_ANY_ID, 0, 0, netmos_9805 },
      { PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9815,
        PCI_ANY_ID, PCI_ANY_ID, 0, 0, netmos_9815 },
      { 0, } /* terminate list */
};
MODULE_DEVICE_TABLE(pci,parport_pc_pci_tbl);

struct pci_parport_data {
      int num;
      struct parport *ports[2];
};

static int parport_pc_pci_probe (struct pci_dev *dev,
                                 const struct pci_device_id *id)
{
      int err, count, n, i = id->driver_data;
      struct pci_parport_data *data;

      if (i < last_sio)
            /* This is an onboard Super-IO and has already been probed */
            return 0;

      /* This is a PCI card */
      i -= last_sio;
      count = 0;
      if ((err = pci_enable_device (dev)) != 0)
            return err;

      data = kmalloc(sizeof(struct pci_parport_data), GFP_KERNEL);
      if (!data)
            return -ENOMEM;

      if (cards[i].preinit_hook &&
          cards[i].preinit_hook (dev, PARPORT_IRQ_NONE, PARPORT_DMA_NONE)) {
            kfree(data);
            return -ENODEV;
      }

      for (n = 0; n < cards[i].numports; n++) {
            int lo = cards[i].addr[n].lo;
            int hi = cards[i].addr[n].hi;
            unsigned long io_lo, io_hi;
            io_lo = pci_resource_start (dev, lo);
            io_hi = 0;
            if ((hi >= 0) && (hi <= 6))
                  io_hi = pci_resource_start (dev, hi);
            else if (hi > 6)
                  io_lo += hi; /* Reinterpret the meaning of
                                        "hi" as an offset (see SYBA
                                        def.) */
            /* TODO: test if sharing interrupts works */
            printk (KERN_DEBUG "PCI parallel port detected: %04x:%04x, "
                  "I/O at %#lx(%#lx)\n",
                  parport_pc_pci_tbl[i + last_sio].vendor,
                  parport_pc_pci_tbl[i + last_sio].device, io_lo, io_hi);
            data->ports[count] =
                  parport_pc_probe_port (io_lo, io_hi, PARPORT_IRQ_NONE,
                                     PARPORT_DMA_NONE, &dev->dev);
            if (data->ports[count])
                  count++;
      }

      data->num = count;

      if (cards[i].postinit_hook)
            cards[i].postinit_hook (dev, count == 0);

      if (count) {
            pci_set_drvdata(dev, data);
            return 0;
      }

      kfree(data);

      return -ENODEV;
}

static void __devexit parport_pc_pci_remove(struct pci_dev *dev)
{
      struct pci_parport_data *data = pci_get_drvdata(dev);
      int i;

      pci_set_drvdata(dev, NULL);

      if (data) {
            for (i = data->num - 1; i >= 0; i--)
                  parport_pc_unregister_port(data->ports[i]);

            kfree(data);
      }
}

static struct pci_driver parport_pc_pci_driver = {
      .name       = "parport_pc",
      .id_table   = parport_pc_pci_tbl,
      .probe            = parport_pc_pci_probe,
      .remove           = __devexit_p(parport_pc_pci_remove),
};

static int __init parport_pc_init_superio (int autoirq, int autodma)
{
      const struct pci_device_id *id;
      struct pci_dev *pdev = NULL;
      int ret = 0;

      for_each_pci_dev(pdev) {
            id = pci_match_id(parport_pc_pci_tbl, pdev);
            if (id == NULL || id->driver_data >= last_sio)
                  continue;

            if (parport_pc_superio_info[id->driver_data].probe
                  (pdev, autoirq, autodma,parport_pc_superio_info[id->driver_data].via)) {
                  ret++;
            }
      }

      return ret; /* number of devices found */
}
#else
static struct pci_driver parport_pc_pci_driver;
static int __init parport_pc_init_superio(int autoirq, int autodma) {return 0;}
#endif /* CONFIG_PCI */


static const struct pnp_device_id parport_pc_pnp_tbl[] = {
      /* Standard LPT Printer Port */
      {.id = "PNP0400", .driver_data = 0},
      /* ECP Printer Port */
      {.id = "PNP0401", .driver_data = 0},
      { }
};

MODULE_DEVICE_TABLE(pnp,parport_pc_pnp_tbl);

static int parport_pc_pnp_probe(struct pnp_dev *dev, const struct pnp_device_id *id)
{
      struct parport *pdata;
      unsigned long io_lo, io_hi;
      int dma, irq;

      if (pnp_port_valid(dev,0) &&
            !(pnp_port_flags(dev,0) & IORESOURCE_DISABLED)) {
            io_lo = pnp_port_start(dev,0);
      } else
            return -EINVAL;

      if (pnp_port_valid(dev,1) &&
            !(pnp_port_flags(dev,1) & IORESOURCE_DISABLED)) {
            io_hi = pnp_port_start(dev,1);
      } else
            io_hi = 0;

      if (pnp_irq_valid(dev,0) &&
            !(pnp_irq_flags(dev,0) & IORESOURCE_DISABLED)) {
            irq = pnp_irq(dev,0);
      } else
            irq = PARPORT_IRQ_NONE;

      if (pnp_dma_valid(dev,0) &&
            !(pnp_dma_flags(dev,0) & IORESOURCE_DISABLED)) {
            dma = pnp_dma(dev,0);
      } else
            dma = PARPORT_DMA_NONE;

      dev_info(&dev->dev, "reported by %s\n", dev->protocol->name);
      if (!(pdata = parport_pc_probe_port (io_lo, io_hi, irq, dma, &dev->dev)))
            return -ENODEV;

      pnp_set_drvdata(dev,pdata);
      return 0;
}

static void parport_pc_pnp_remove(struct pnp_dev *dev)
{
      struct parport *pdata = (struct parport *)pnp_get_drvdata(dev);
      if (!pdata)
            return;

      parport_pc_unregister_port(pdata);
}

/* we only need the pnp layer to activate the device, at least for now */
static struct pnp_driver parport_pc_pnp_driver = {
      .name       = "parport_pc",
      .id_table   = parport_pc_pnp_tbl,
      .probe            = parport_pc_pnp_probe,
      .remove           = parport_pc_pnp_remove,
};


static int __devinit parport_pc_platform_probe(struct platform_device *pdev)
{
      /* Always succeed, the actual probing is done in
       * parport_pc_probe_port(). */
      return 0;
}

static struct platform_driver parport_pc_platform_driver = {
      .driver = {
            .owner      = THIS_MODULE,
            .name = "parport_pc",
      },
      .probe            = parport_pc_platform_probe,
};

/* This is called by parport_pc_find_nonpci_ports (in asm/parport.h) */
static int __devinit __attribute__((unused))
parport_pc_find_isa_ports (int autoirq, int autodma)
{
      int count = 0;

      if (parport_pc_probe_port(0x3bc, 0x7bc, autoirq, autodma, NULL))
            count++;
      if (parport_pc_probe_port(0x378, 0x778, autoirq, autodma, NULL))
            count++;
      if (parport_pc_probe_port(0x278, 0x678, autoirq, autodma, NULL))
            count++;

      return count;
}

/* This function is called by parport_pc_init if the user didn't
 * specify any ports to probe.  Its job is to find some ports.  Order
 * is important here -- we want ISA ports to be registered first,
 * followed by PCI cards (for least surprise), but before that we want
 * to do chipset-specific tests for some onboard ports that we know
 * about.
 *
 * autoirq is PARPORT_IRQ_NONE, PARPORT_IRQ_AUTO, or PARPORT_IRQ_PROBEONLY
 * autodma is PARPORT_DMA_NONE or PARPORT_DMA_AUTO
 */
static void __init parport_pc_find_ports (int autoirq, int autodma)
{
      int count = 0, err;

#ifdef CONFIG_PARPORT_PC_SUPERIO
      detect_and_report_winbond ();
      detect_and_report_smsc ();
#endif

      /* Onboard SuperIO chipsets that show themselves on the PCI bus. */
      count += parport_pc_init_superio (autoirq, autodma);

      /* PnP ports, skip detection if SuperIO already found them */
      if (!count) {
            err = pnp_register_driver (&parport_pc_pnp_driver);
            if (!err)
                  pnp_registered_parport = 1;
      }

      /* ISA ports and whatever (see asm/parport.h). */
      parport_pc_find_nonpci_ports (autoirq, autodma);

      err = pci_register_driver (&parport_pc_pci_driver);
      if (!err)
            pci_registered_parport = 1;
}

/*
 *    Piles of crap below pretend to be a parser for module and kernel
 *    parameters.  Say "thank you" to whoever had come up with that
 *    syntax and keep in mind that code below is a cleaned up version.
 */

static int __initdata io[PARPORT_PC_MAX_PORTS+1] = { [0 ... PARPORT_PC_MAX_PORTS] = 0 };
static int __initdata io_hi[PARPORT_PC_MAX_PORTS+1] =
      { [0 ... PARPORT_PC_MAX_PORTS] = PARPORT_IOHI_AUTO };
static int __initdata dmaval[PARPORT_PC_MAX_PORTS] = { [0 ... PARPORT_PC_MAX_PORTS-1] = PARPORT_DMA_NONE };
static int __initdata irqval[PARPORT_PC_MAX_PORTS] = { [0 ... PARPORT_PC_MAX_PORTS-1] = PARPORT_IRQ_PROBEONLY };

static int __init parport_parse_param(const char *s, int *val,
                        int automatic, int none, int nofifo)
{
      if (!s)
            return 0;
      if (!strncmp(s, "auto", 4))
            *val = automatic;
      else if (!strncmp(s, "none", 4))
            *val = none;
      else if (nofifo && !strncmp(s, "nofifo", 4))
            *val = nofifo;
      else {
            char *ep;
            unsigned long r = simple_strtoul(s, &ep, 0);
            if (ep != s)
                  *val = r;
            else {
                  printk(KERN_ERR "parport: bad specifier `%s'\n", s);
                  return -1;
            }
      }
      return 0;
}

static int __init parport_parse_irq(const char *irqstr, int *val)
{
      return parport_parse_param(irqstr, val, PARPORT_IRQ_AUTO,
                             PARPORT_IRQ_NONE, 0);
}

static int __init parport_parse_dma(const char *dmastr, int *val)
{
      return parport_parse_param(dmastr, val, PARPORT_DMA_AUTO,
                             PARPORT_DMA_NONE, PARPORT_DMA_NOFIFO);
}

#ifdef CONFIG_PCI
static int __init parport_init_mode_setup(char *str)
{
      printk(KERN_DEBUG "parport_pc.c: Specified parameter parport_init_mode=%s\n", str);

      if (!strcmp (str, "spp"))
            parport_init_mode=1;
      if (!strcmp (str, "ps2"))
            parport_init_mode=2;
      if (!strcmp (str, "epp"))
            parport_init_mode=3;
      if (!strcmp (str, "ecp"))
            parport_init_mode=4;
      if (!strcmp (str, "ecpepp"))
            parport_init_mode=5;
      return 1;
}
#endif

#ifdef MODULE
static const char *irq[PARPORT_PC_MAX_PORTS];
static const char *dma[PARPORT_PC_MAX_PORTS];

MODULE_PARM_DESC(io, "Base I/O address (SPP regs)");
module_param_array(io, int, NULL, 0);
MODULE_PARM_DESC(io_hi, "Base I/O address (ECR)");
module_param_array(io_hi, int, NULL, 0);
MODULE_PARM_DESC(irq, "IRQ line");
module_param_array(irq, charp, NULL, 0);
MODULE_PARM_DESC(dma, "DMA channel");
module_param_array(dma, charp, NULL, 0);
#if defined(CONFIG_PARPORT_PC_SUPERIO) || \
       (defined(CONFIG_PARPORT_1284) && defined(CONFIG_PARPORT_PC_FIFO))
MODULE_PARM_DESC(verbose_probing, "Log chit-chat during initialisation");
module_param(verbose_probing, int, 0644);
#endif
#ifdef CONFIG_PCI
static char *init_mode;
MODULE_PARM_DESC(init_mode, "Initialise mode for VIA VT8231 port (spp, ps2, epp, ecp or ecpepp)");
module_param(init_mode, charp, 0);
#endif

static int __init parse_parport_params(void)
{
      unsigned int i;
      int val;

#ifdef CONFIG_PCI
      if (init_mode)
            parport_init_mode_setup(init_mode);
#endif

      for (i = 0; i < PARPORT_PC_MAX_PORTS && io[i]; i++) {
            if (parport_parse_irq(irq[i], &val))
                  return 1;
            irqval[i] = val;
            if (parport_parse_dma(dma[i], &val))
                  return 1;
            dmaval[i] = val;
      }
      if (!io[0]) {
            /* The user can make us use any IRQs or DMAs we find. */
            if (irq[0] && !parport_parse_irq(irq[0], &val))
                  switch (val) {
                  case PARPORT_IRQ_NONE:
                  case PARPORT_IRQ_AUTO:
                        irqval[0] = val;
                        break;
                  default:
                        printk (KERN_WARNING
                              "parport_pc: irq specified "
                              "without base address.  Use 'io=' "
                              "to specify one\n");
                  }

            if (dma[0] && !parport_parse_dma(dma[0], &val))
                  switch (val) {
                  case PARPORT_DMA_NONE:
                  case PARPORT_DMA_AUTO:
                        dmaval[0] = val;
                        break;
                  default:
                        printk (KERN_WARNING
                              "parport_pc: dma specified "
                              "without base address.  Use 'io=' "
                              "to specify one\n");
                  }
      }
      return 0;
}

#else

static int parport_setup_ptr __initdata = 0;

/*
 * Acceptable parameters:
 *
 * parport=0
 * parport=auto
 * parport=0xBASE[,IRQ[,DMA]]
 *
 * IRQ/DMA may be numeric or 'auto' or 'none'
 */
static int __init parport_setup (char *str)
{
      char *endptr;
      char *sep;
      int val;

      if (!str || !*str || (*str == '0' && !*(str+1))) {
            /* Disable parport if "parport=0" in cmdline */
            io[0] = PARPORT_DISABLE;
            return 1;
      }

      if (!strncmp (str, "auto", 4)) {
            irqval[0] = PARPORT_IRQ_AUTO;
            dmaval[0] = PARPORT_DMA_AUTO;
            return 1;
      }

      val = simple_strtoul (str, &endptr, 0);
      if (endptr == str) {
            printk (KERN_WARNING "parport=%s not understood\n", str);
            return 1;
      }

      if (parport_setup_ptr == PARPORT_PC_MAX_PORTS) {
            printk(KERN_ERR "parport=%s ignored, too many ports\n", str);
            return 1;
      }

      io[parport_setup_ptr] = val;
      irqval[parport_setup_ptr] = PARPORT_IRQ_NONE;
      dmaval[parport_setup_ptr] = PARPORT_DMA_NONE;

      sep = strchr(str, ',');
      if (sep++) {
            if (parport_parse_irq(sep, &val))
                  return 1;
            irqval[parport_setup_ptr] = val;
            sep = strchr(sep, ',');
            if (sep++) {
                  if (parport_parse_dma(sep, &val))
                        return 1;
                  dmaval[parport_setup_ptr] = val;
            }
      }
      parport_setup_ptr++;
      return 1;
}

static int __init parse_parport_params(void)
{
      return io[0] == PARPORT_DISABLE;
}

__setup ("parport=", parport_setup);

/*
 * Acceptable parameters:
 *
 * parport_init_mode=[spp|ps2|epp|ecp|ecpepp]
 */
#ifdef CONFIG_PCI
__setup("parport_init_mode=",parport_init_mode_setup);
#endif
#endif

/* "Parser" ends here */

static int __init parport_pc_init(void)
{
      int err;

      if (parse_parport_params())
            return -EINVAL;

      err = platform_driver_register(&parport_pc_platform_driver);
      if (err)
            return err;

      if (io[0]) {
            int i;
            /* Only probe the ports we were given. */
            user_specified = 1;
            for (i = 0; i < PARPORT_PC_MAX_PORTS; i++) {
                  if (!io[i])
                        break;
                  if ((io_hi[i]) == PARPORT_IOHI_AUTO)
                         io_hi[i] = 0x400 + io[i];
                  parport_pc_probe_port(io[i], io_hi[i],
                                      irqval[i], dmaval[i], NULL);
            }
      } else
            parport_pc_find_ports (irqval[0], dmaval[0]);

      return 0;
}

static void __exit parport_pc_exit(void)
{
      if (pci_registered_parport)
            pci_unregister_driver (&parport_pc_pci_driver);
      if (pnp_registered_parport)
            pnp_unregister_driver (&parport_pc_pnp_driver);
      platform_driver_unregister(&parport_pc_platform_driver);

      while (!list_empty(&ports_list)) {
            struct parport_pc_private *priv;
            struct parport *port;
            priv = list_entry(ports_list.next,
                          struct parport_pc_private, list);
            port = priv->port;
            if (port->dev && port->dev->bus == &platform_bus_type)
                  platform_device_unregister(
                        to_platform_device(port->dev));
            parport_pc_unregister_port(port);
      }
}

MODULE_AUTHOR("Phil Blundell, Tim Waugh, others");
MODULE_DESCRIPTION("PC-style parallel port driver");
MODULE_LICENSE("GPL");
module_init(parport_pc_init)
module_exit(parport_pc_exit)

Generated by  Doxygen 1.6.0   Back to index