Logo Search packages:      
Sourcecode: linux version File versions  Download package


 *      linux/drivers/char/specialix_io8.h  -- 
 *                                   Specialix IO8+ multiport serial driver.
 *      Copyright (C) 1997 Roger Wolff (R.E.Wolff@BitWizard.nl)
 *      Copyright (C) 1994-1996  Dmitry Gorodchanin (pgmdsg@ibi.com)
 *      Specialix pays for the development and support of this driver.
 *      Please DO contact io8-linux@specialix.co.uk if you require
 *      support.
 *      This driver was developped in the BitWizard linux device
 *      driver service. If you require a linux device driver for your
 *      product, please contact devices@BitWizard.nl for a quote.
 *      This code is firmly based on the riscom/8 serial driver,
 *      written by Dmitry Gorodchanin. The specialix IO8+ card
 *      programming information was obtained from the CL-CD1865 Data
 *      Book, and Specialix document number 6200059: IO8+ Hardware
 *      Functional Specification.
 *      This program is free software; you can redistribute it and/or
 *      modify it under the terms of the GNU General Public License as
 *      published by the Free Software Foundation; either version 2 of
 *      the License, or (at your option) any later version.
 *      This program is distributed in the hope that it will be
 *      useful, but WITHOUT ANY WARRANTY; without even the implied
 *      PURPOSE.  See the GNU General Public License for more details.
 *      You should have received a copy of the GNU General Public
 *      License along with this program; if not, write to the Free
 *      Software Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139,
 *      USA.
 * */


#include <linux/serial.h>

#ifdef __KERNEL__

/* You can have max 4 ISA cards in one PC, and I recommend not much 
more than a few  PCI versions of the card. */

#define SX_NBOARD       8

/* NOTE: Specialix decoder recognizes 4 addresses, but only two are used.... */
#define SX_IO_SPACE             4
/* The PCI version decodes 8 addresses, but still only 2 are used. */
#define SX_PCI_IO_SPACE         8

/* eight ports per board. */
#define SX_NPORT              8
#define SX_BOARD(line)        ((line) / SX_NPORT)
#define SX_PORT(line)         ((line) & (SX_NPORT - 1))

#define SX_DATA_REG 0     /* Base+0 : Data register */
#define SX_ADDR_REG 1     /* base+1 : Address register. */

#define MHz *1000000    /* I'm ashamed of myself. */

/* On-board oscillator frequency */
#define SX_OSCFREQ      (25 MHz/2)
/* There is a 25MHz crystal on the board, but the chip is in /2 mode */

/* Ticks per sec. Used for setting receiver timeout and break length */
#define SPECIALIX_TPS         4000

/* Yeah, after heavy testing I decided it must be 6.
 * Sure, You can change it if needed.
#define SPECIALIX_RXFIFO      6     /* Max. receiver FIFO size (1-8) */

#define SPECIALIX_MAGIC       0x0907

#define SX_CCR_TIMEOUT 10000   /* CCR timeout. You may need to wait upto
                                  10 milliseconds before the internal
                                  processor is available again after
                                  you give it a command */

#define SX_IOBASE1      0x100
#define SX_IOBASE2      0x180
#define SX_IOBASE3      0x250
#define SX_IOBASE4      0x260

struct specialix_board {
      unsigned long   flags;
      unsigned short    base;
      unsigned char     irq;
      //signed   char   count;
      int count;
      unsigned char     DTR;
        int reg;
      spinlock_t lock;

#define SX_BOARD_PRESENT      0x00000001
#define SX_BOARD_ACTIVE       0x00000002
#define SX_BOARD_IS_PCI       0x00000004

struct specialix_port {
      int               magic;
      int               baud_base;
      int               flags;
      struct tty_struct       * tty;
      int               count;
      int               blocked_open;
      ulong             event;
      int               timeout;
      int               close_delay;
      unsigned char           * xmit_buf;
      int               custom_divisor;
      int               xmit_head;
      int               xmit_tail;
      int               xmit_cnt;
      wait_queue_head_t open_wait;
      wait_queue_head_t close_wait;
      struct work_struct      tqueue;
      struct work_struct      tqueue_hangup;
      short             wakeup_chars;
      short             break_length;
      unsigned short          closing_wait;
      unsigned char           mark_mask;
      unsigned char           IER;
      unsigned char           MSVR;
      unsigned char           COR2;
      unsigned long           overrun;
      unsigned long           hits[10];
      spinlock_t lock;

#endif /* __KERNEL__ */
#endif /* __LINUX_SPECIALIX_H */

Generated by  Doxygen 1.6.0   Back to index