Logo Search packages:      
Sourcecode: linux version File versions  Download package

yucca.h

/*
 * Yucca board definitions
 *
 * Roland Dreier <rolandd@cisco.com> (based on luan.h by Matt Porter)
 *
 * Copyright 2004-2005 MontaVista Software Inc.
 * Copyright (c) 2005 Cisco Systems.  All rights reserved.
 *
 * This program is free software; you can redistribute  it and/or modify it
 * under  the terms of  the GNU General  Public License as published by the
 * Free Software Foundation;  either version 2 of the  License, or (at your
 * option) any later version.
 *
 */

#ifdef __KERNEL__
#ifndef __ASM_YUCCA_H__
#define __ASM_YUCCA_H__

#include <platforms/4xx/ppc440spe.h>

/* F/W TLB mapping used in bootloader glue to reset EMAC */
#define PPC44x_EMAC0_MR0      0xa0000800

/* Location of MAC addresses in PIBS image */
#define PIBS_FLASH_BASE       0xffe00000
#define PIBS_MAC_BASE         (PIBS_FLASH_BASE+0x1b0400)

/* External timer clock frequency */
#define YUCCA_TMR_CLK         25000000

/*
 * FPGA registers
 */
#define YUCCA_FPGA_REG_BASE               0x00000004e2000000ULL
#define YUCCA_FPGA_REG_SIZE               0x24

#define FPGA_REG1A                        0x1a

#define FPGA_REG1A_PE0_GLED               0x8000
#define FPGA_REG1A_PE1_GLED               0x4000
#define FPGA_REG1A_PE2_GLED               0x2000
#define FPGA_REG1A_PE0_YLED               0x1000
#define FPGA_REG1A_PE1_YLED               0x0800
#define FPGA_REG1A_PE2_YLED               0x0400
#define FPGA_REG1A_PE0_PWRON              0x0200
#define FPGA_REG1A_PE1_PWRON              0x0100
#define FPGA_REG1A_PE2_PWRON              0x0080
#define FPGA_REG1A_PE0_REFCLK_ENABLE            0x0040
#define FPGA_REG1A_PE1_REFCLK_ENABLE            0x0020
#define FPGA_REG1A_PE2_REFCLK_ENABLE            0x0010
#define FPGA_REG1A_PE_SPREAD0             0x0008
#define FPGA_REG1A_PE_SPREAD1             0x0004
#define FPGA_REG1A_PE_SELSOURCE_0         0x0002
#define FPGA_REG1A_PE_SELSOURCE_1         0x0001

#define FPGA_REG1C                        0x1c

#define FPGA_REG1C_PE0_ROOTPOINT          0x8000
#define FPGA_REG1C_PE1_ENDPOINT                 0x4000
#define FPGA_REG1C_PE2_ENDPOINT                 0x2000
#define FPGA_REG1C_PE0_PRSNT              0x1000
#define FPGA_REG1C_PE1_PRSNT              0x0800
#define FPGA_REG1C_PE2_PRSNT              0x0400
#define FPGA_REG1C_PE0_WAKE               0x0080
#define FPGA_REG1C_PE1_WAKE               0x0040
#define FPGA_REG1C_PE2_WAKE               0x0020
#define FPGA_REG1C_PE0_PERST              0x0010
#define FPGA_REG1C_PE1_PERST              0x0008
#define FPGA_REG1C_PE2_PERST              0x0004

/*
 * Serial port defines
 */
#define RS_TABLE_SIZE   3

/* PIBS defined UART mappings, used before early_serial_setup */
#define UART0_IO_BASE   0xa0000200
#define UART1_IO_BASE   0xa0000300
#define UART2_IO_BASE   0xa0000600

#define BASE_BAUD 11059200
#define STD_UART_OP(num)                              \
      { 0, BASE_BAUD, 0, UART##num##_INT,             \
            (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST),  \
            iomem_base: (void*)UART##num##_IO_BASE,         \
            io_type: SERIAL_IO_MEM},

#define SERIAL_PORT_DFNS      \
      STD_UART_OP(0)          \
      STD_UART_OP(1)          \
      STD_UART_OP(2)

/* PCI support */
#define YUCCA_PCIX_LOWER_IO   0x00000000
#define YUCCA_PCIX_UPPER_IO   0x0000ffff
#define YUCCA_PCIX_LOWER_MEM  0x80000000
#define YUCCA_PCIX_UPPER_MEM  0x8fffffff
#define YUCCA_PCIE_LOWER_MEM  0x90000000
#define YUCCA_PCIE_MEM_SIZE   0x10000000

#define YUCCA_PCIX_MEM_SIZE   0x10000000
#define YUCCA_PCIX_MEM_OFFSET 0x00000000
#define YUCCA_PCIE_MEM_SIZE   0x10000000
#define YUCCA_PCIE_MEM_OFFSET 0x00000000

#endif                        /* __ASM_YUCCA_H__ */
#endif                        /* __KERNEL__ */

Generated by  Doxygen 1.6.0   Back to index