Logo Search packages:      
Sourcecode: linux version File versions  Download package

tsx1x-common.c

#include <linux/kernel.h>
#include <linux/pci.h>
#include <linux/platform_device.h>
#include <linux/mtd/physmap.h>
#include <linux/spi/flash.h>
#include <linux/spi/spi.h>
#include <linux/spi/orion_spi.h>
#include <linux/serial_reg.h>
#include <mach/kirkwood.h>
#include "common.h"

/*
 * QNAP TS-x1x Boards flash
 */

/****************************************************************************
 * 16 MiB NOR flash. The struct mtd_partition is not in the same order as the
 *     partitions on the device because we want to keep compatability with
 *     the QNAP firmware.
 * Layout as used by QNAP:
 *  0x00000000-0x00080000 : "U-Boot"
 *  0x00200000-0x00400000 : "Kernel"
 *  0x00400000-0x00d00000 : "RootFS"
 *  0x00d00000-0x01000000 : "RootFS2"
 *  0x00080000-0x000c0000 : "U-Boot Config"
 *  0x000c0000-0x00200000 : "NAS Config"
 *
 * We'll use "RootFS1" instead of "RootFS" to stay compatible with the layout
 * used by the QNAP TS-109/TS-209.
 *
 ***************************************************************************/

struct mtd_partition qnap_tsx1x_partitions[] = {
      {
            .name       = "U-Boot",
            .size       = 0x00080000,
            .offset           = 0,
            .mask_flags = MTD_WRITEABLE,
      }, {
            .name       = "Kernel",
            .size       = 0x00200000,
            .offset           = 0x00200000,
      }, {
            .name       = "RootFS1",
            .size       = 0x00900000,
            .offset           = 0x00400000,
      }, {
            .name       = "RootFS2",
            .size       = 0x00300000,
            .offset           = 0x00d00000,
      }, {
            .name       = "U-Boot Config",
            .size       = 0x00040000,
            .offset           = 0x00080000,
      }, {
            .name       = "NAS Config",
            .size       = 0x00140000,
            .offset           = 0x000c0000,
      },
};

const struct flash_platform_data qnap_tsx1x_flash = {
      .type       = "m25p128",
      .name       = "spi_flash",
      .parts            = qnap_tsx1x_partitions,
      .nr_parts   = ARRAY_SIZE(qnap_tsx1x_partitions),
};

struct spi_board_info __initdata qnap_tsx1x_spi_slave_info[] = {
      {
            .modalias   = "m25p80",
            .platform_data    = &qnap_tsx1x_flash,
            .irq        = -1,
            .max_speed_hz     = 20000000,
            .bus_num    = 0,
            .chip_select      = 0,
      },
};

void __init qnap_tsx1x_register_flash(void)
{
      spi_register_board_info(qnap_tsx1x_spi_slave_info,
                        ARRAY_SIZE(qnap_tsx1x_spi_slave_info));
      kirkwood_spi_init();
}


/*****************************************************************************
 * QNAP TS-x1x specific power off method via UART1-attached PIC
 ****************************************************************************/

#define UART1_REG(x)    (UART1_VIRT_BASE + ((UART_##x) << 2))

void qnap_tsx1x_power_off(void)
{
      /* 19200 baud divisor */
      const unsigned divisor = ((kirkwood_tclk + (8 * 19200)) / (16 * 19200));

      pr_info("%s: triggering power-off...\n", __func__);

      /* hijack UART1 and reset into sane state (19200,8n1) */
      writel(0x83, UART1_REG(LCR));
      writel(divisor & 0xff, UART1_REG(DLL));
      writel((divisor >> 8) & 0xff, UART1_REG(DLM));
      writel(0x03, UART1_REG(LCR));
      writel(0x00, UART1_REG(IER));
      writel(0x00, UART1_REG(FCR));
      writel(0x00, UART1_REG(MCR));

      /* send the power-off command 'A' to PIC */
      writel('A', UART1_REG(TX));
}


Generated by  Doxygen 1.6.0   Back to index